I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi,
We have experienced some unknown resets in our devices specifically when woken up after being in storage for a prolonged period in ULP mode - about a year or so. Afterwards...
Hello!
I'm writing an application that uses MQTT to post some sensor data to a server. My networking code is basically a duplicate of this sample , except I set up the LTE...
Hello -
I was nearing completion of a BLE Mesh project with the NRF52840 when there became a shortage of NRF52840 QFN. I decided to migrate back to the NRF52832 and reworked...
Hello, I’m testing a circuit built with the nPM1300. When connecting or disconnecting power via USB-C, noise is generated at the circuit's button, causing unintended signals...
I work currently working on a driver module supporting your nRF91x1. I schedule rx-operations via your nrf_modem_dect_phy_rx() dect_phy modem-api. I am using the .handle field...
Hi All,
I am exploring nrf54l15 which has rram 1524KB. However, noticed that not able to access beyond 1428KB.
When build sample hello world code found that only 1428KB...
I am currently trying to get LLEXTs to work on the nRF5340 Audio DK. I was able to compile an llext and load it successfully, using the cmake features, However, I would like...
I've testing out the GNSS and Location samples. According to documentation, A-GNSS is enabled by default in the location sample but I am not able to confirm this both through...
Good Afternoon,
I am working on getting the npm1300 up and running on my custom board. I have a 1v8 line and a 3v2 line with the load switches being used as LDOs. I am using...
Hi,
I'm working on an indoor positioning system using an nRF5340 and a CHW1010-ANT1 antenna array. I'm receiving IQ samples from BLE CTE packets and using them to calculate...
While using the nRF9151 DK , after inserting the onomondo sim and connecting, the Cellular Monitor SIM sections appears the Wireless Logic ICCID number instead of onomondo...
Hi,
We are developing a product with WIFI+BLE and we are using nRF7002DK as the base. The important function is OTA because our functions may be changed after the hardware...
Hello,
I used to be working with the nrf sdk 2.7.0. For running unit tests for my project I build and run the unit test application for qemu_cortex_m3 like this:
...
Hi i am facing the issue with initializing the peripherals when the device is wake up from the deep sleep this are the logs i am getting after wake up this taking to log to...
Hello,
We are currently evaluating the nPM1300 as a key component on one of our new designs. This design must support both USB and solar charging using relatively low power...
