Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
In the documentation for the secure bootloader, it's mentioned that the provisioning data gets stored in OTP memory for some chips (e.g. nRF5340). Is there a way to know what...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
Device Overview
We have developed a smart wearable that sends notifications to our mobile application over BLE. Under normal conditions, the device alternates sensor...
Hello,
I'd like to ask what needs to be configured to enable communication between two boards: nrF7002-DK and nRF5340-DK via another UART (e.g. UART1).
Please provide...
Hi Team,
We are developing on a custom board with an nRF54L15 (Raytac Module with NRF54L15_xxAA_ENGB) and are unable to provision a pre-generated secp256r1 private key into...
Hi, I want to run Bluetooth Mesh Light example on nrf54h20 chip.
At the beginning I prepared devboard with this tutorial: https://docs.nordicsemi.com/bundle/ncs-latest/page...
HI ,ALL
i need to take use of the pstorage module.
i can read the data after reset,but i do not know the reason.
the write function is added in the on_write...
Hi there,
I have a nrf51422CEAA chip with 16k variant with single bank bootloader code. I compile it using (03) optimazation and the final result is :
"Program Size...
Hello,
I just produced my custom board with nRF52 but i have a problem.
I can program it (SWD over nRF52 DK), debug it (segger debudder software) but in bootloader it...
hi there,
I am using this tutorial to add dfu to nrf51422_xxac_s130 beacon application. however Im getting these linking errors:
._build\nrf51422_xxac_s130.axf: Error...
I was wondering what the procedure it for questions asked over the weekend. Obviously you guys are only available at office hours (Norway time I'm guessing?), so how do you...
I was kindly surprised with new S130 functionality - ECDH key exchange. Do you have plans in the near future to implement it in S110 softdevice? Thanks
Hi
I have nrf51822 CEAA which is powered with 1.9 volt on vdd (low power chip). I'm using ADC to measure battery level but the conversion gave me 5.4 volt wich is wrong for...
Hi,
we have developed some software that is running fine on the nRF52-DK (PCA10040 v0.9.0) which uses nRF52832 IC revision "Engineering B".
We are using SoftDevice s132_nrf52_2...
Hey everyone,
I am using nrf51 dongle pca 10031. Nordic promised to have 1Mbps data rate. when i was trying to transfer data through UART. data is validated until 401600...
hi
im working with nrf51422 and keil and s130
my external crystal is a 32768 and 16 mega
for my soft-device witch one should i use
// Initialize SoftDevice.
SOFTDEVICE_HANDLER_INIT...
I'm trying to add a characteristic to a service in nRFGo Studio with the Write propery enabled.
However, the software doesn't allow me to enable Write and greys the checkbox...
Hi,
i am using nrf51822 for my application.
i am using connectable undirected mode with 40 ms advertising interval but when i am seeing the device data in the nrf master...
hi,
i am using sdk 10, with s120.
i want to advertise data on a single channel with frequency say (2426).
is there any sample code or something, with which i can play...
Is there a hook anywhere in the SD (130/132) to let me generate my own LTKs, EDIV and RAND during the bonding process? I don't think so, I've not found one, but perhaps I...
Good afternoon.
I´m using nrf51-dk with SDK 9.0.0, s110 softdevice and uart nordic app on mobile. I have a program in my nrf51-dk that it sends and receives data between...
