Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
Hey. I want to wake my s110 device every 30-40 second to advertise for a few seconds only. Is there an example on this or if someone could guide me in the right direction...
Hi all,
I need to using NRF51822 as a clock: second, min, hour, date.... I know I only use RTC as a timer 1s. When NRF51822 power off then time was lost. So, I must be...
Hello,
I have some problem with a specific phone. I try to connect with the nrf52832 using samsung S3 with android version 5.1, the connection takes 20 - 50 seconds and...
Hi,
I am very new to nrf51822 controller. I Used STM32 cortex controller's.
I want to know basic hardware which are the require to start nrf51822 working and programming...
The example nRF51-DK gerbers have solder mask on the PCB antenna. But for the nRF24L01+ EK gerbers, the PCB antenna has the solder mask removed partially, along the length...
Hi,
I downloaded the nrF5 SDK V12.2 from:
www.nordicsemi.com/.../nRF5-SDK
after unzip, I could see the SDCard library under "\nRF5_SDK_12.2.0_f012efa\components\libraries...
Following III. Example code and Enabling whitelisting ,
I try to connect to the "nRF52 DK" board with a whitelist (Android BLE device address),
but I've never connected...
1、I use SDK9.0 ANCS project, the position is as follows:
SDK9.0\examples\ble_peripheral\ble_app_ancs_c\pca10028\s110\arm4
2、I need a project which is contained with...
hello there,
i am giving external supply to nrf51. my external supply is usb 3.3 v. but when i connect it with nordic and then if i check it on multimeter , it shows me...
Hi all,
Does anyone know how much current is meant to be drawn to discover nearby devices? I guess, in other words, how much current is drawn to put the nRF51822 in discovery...
Hi Sir,
I have a NRF 51822 board & MPU 9250 sensor.
I want to read YAW,PITCH,ROLL,ACC_X,ACC_Y,ACC_Z,GX,GY,GZ,MX,MY,MZ values from MPU Sensor.
Could you please share...
Hi All,
Continuing on with my project: a custom board containing nRF52 + ECG front end.
Successfully integrates SPI functionality; need 2 more interfaces:
32...
Previously you recommended using S132 v4.0.0 2. alpha release to get more than 8 central connections. As far as I know this revision doesn't implement Bluetooth 5.0 protocol...
Hi,
I have written a code which transmits data over BLE.
The board was getting reset.
What we changed is instead of sending application data we sent the RESETREAS register...
Hi,
I'm trying to change the MAC address of nrf52, using softdevice s132_nrf52_3.1.0 but we dont have sd_ble_gap_address_get() and sd_ble_gap_address_set() APIs in "ble_gap...
