If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
Not really sure where the problem is here, my guess is in the code... I just recently saw this: https://www.avrfreaks.net/comment/1342846#comment-1342846
Although my issue...
Hi,
I used the ble_peripheral and ble_central example and I send messages from one to the other.
Know I need to do the same with multilink.
I managed to connect ble_multilink_central...
hi dear Engineers!
the questions is it possible to use RX RF reciever to estimate the average BW RF signal input power like I do it in Semtech 433/868 RF SoC to make desicion...
hi, all
my nrf52832 can not run good when download the program into the flash, and can not run good in debug session mode without breakpoint ， but if I add one breakpoint...
Hi,
I am trying to send L2CAP connection reply by using this "sd_ble_l2cap_ch_conn_reply()",but i am unable to see the packet on wireshark. The incoming connection handle...
Hi I note here that it is recommended to apply solder mask to the ground layer beneath the nRF24L01+ exposed die so they don't connect:
devzone.nordicsemi.com/.../
But...
I'm finding a discrepancy with numbers between the nwp_008 whitepaper (quarterwave printed monopole antenna for 2.45ghz) and AppCad values.
I've assumed you can measure...
Hi.
Months ago I loaded the nfc_url_record example and it worked fine.
Later some time I updated the packages, and since then that particular example gives errors.
The...
Hi,
Anyone familiar/experiened in production-test gear for BLE?
Test sets, i.e. LitePoint, Anritsu, USRP, NI?
What's relevant to test, i.e. output power...
Figure 222 of the OP spec states "important: no components in bottom layer". Are you recommending that we keep the bottom side clear under/near the nRF52840? This feels a...
I met some problems in testing ECDH , the project is the example in E:\Source\NRF52832\nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs...
Hi!
I am using SEGGER Embedded Studio for some of the projects. I do utilize C++ in the projects wherever possible and have found that I cannot make the delete operator...
I am working with nRF24LE1 and I use the Gazzell library. But I need a real time base. I have a chance, because I think Gazzell uses that resource. Is there any way I can...
Hello
I am using gazell on the nRF24LE1.
I would like to know some recommendations on how to estimate a consumption on the side of the device based on the times and repetitions...
