Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hello,
We are currently in the process of developing a custom board containing the nrf5340, which will act as a central for HR devices and a peripheral for data transfers...
I have this main code:
With this overlay:
and this configuration:
I am using a nrf52840 dev board and have connected P0.06 and P0.08.
Why does it not trigger...
Hello everyone,
We are currently working on a custom PCB using the nRF54L15-CAAA.
I am following the steps for setting up a new custom board using the "Create a new...
I am facing the following error. I have referered light switch example and have included all the required configs in the prj_fota.conf file
CONFIG_NCS_SAMPLES_DEFAULTS ...
Hello,
I am working on a custom PCB that involves the NRF5340 and our first iteration of PCBs had soldering issues during assembly for the nRF5340. The nRF5340’s footprint...
Hello Nordic,
I am running a project, use the chipset is nRF54L15, I want to know if there is any USB dongle with software can be used to test BLE function of chip nRF54L15...
Hello, I just try to migrate our developing project from old parent-child build to sysbuild,
But when I build the project with non-secure cpu (with TFM), I get the <err...
Our nrf9151 boards are getting stuck when nrf_modem_lib_init() is called.
We just see this line. Usually, the device gets past it in less than a second.
[00:00:00.376...
Hi
I connected RF Connect for Desktop to "nRF54L15_DK" in my Desktop
when I want to use Direct Test Mode,press Start test bottom,the log show "DTM setup reset command...
Hi,
I am trying to program the custom nRF9160 board using SEGGER JLink/SWD programmer , For same of the boards when connected to custom board and trying to select the device...
Hi,
I'd like to go for sysbuild with my nrf9161 based application but after some trials and errors, I am not able to find which images should be enabled in sysbuild.conf...
Hi,
I am currently developing on the BL54L15 Ezurio development kit with the Nordic chip.
I am using the Nordic v3.0.1 SDK and toolchain with the new manufacturer board...
The VSCode nRF Kconfig extension has very high cpu usage (2 cores at 100%)
When disabling the extension, the cpu usage drops back to normal.
I see the following in the...
Hi everyone, I'm working on a project with Zephyr (v2.9.1) and I'm facing a compilation issue related to managing two SPI devices on different buses ( spi0 and spi2 ).
In...
Hi,
I am currently using 54L15-DK to create a radio test example, but there is a problem when I build the project: - sdk version: v2.9.0 - toolchain version: v2.9.1
...
