Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Hi,
We're evaluating NFC for our project.
I've been testing with a nRF52840DK - PCA10056 Version 3.0.2.
Using the antenna supplied with the Development Kit I am...
Hello support team,
where can I find a simple NCS V3.x.x example in which the central and peripheral are implemented in one device (e.g., nRF54L15)?
Thank you in advance...
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
nRF NCS 3.0.x
Target : nrf5340dk or native_sim
What is the latest recommendation on build environment (assuming preference is a docker image for consistency of build...
Hello, I am having a problem using the Segger IDE. I am using the nRF52-DK and got my SDK download from the following link, nRF5 SDK - nordicsemi.com .
What I did exactly...
Hi,
The URL below does not have the DNs number for v2.9.2, but is it the same as for v2.9.0 and v2.9.1?
https://docs.nordicsemi.com/bundle/comp_matrix_nrf54l15/page/COMP...
I am using the VSCode. After building the project , I want to view the warnings. However, when I click the error message but it will show that the editor could not be found...
Hello, I hope you are well.
I created a new driver for an i2c accelerometer with 2 gpio interrupts, but it does not build properly. When calling `static const struct device...
DPPI is not able to build with SDK 2.8.
The issue seems to be the NRF54L15 has 4 DPPI peripherals, yet the NRFX hal version 2.8 only works with one.
Would it be...
Hello everyone,
I'm working in a ble project that use uart interface. When I sent string data in nrf connect app, the uart_event_handle is not called.
I started my project...
Hi everyone,
I currently installed the latest version of the NRF connect SDK. I started a new build task which executes properly. The task doesn't however stop.
This...
Hello,
I am working on a hardware design with two MEMS PDM microphones and a mono speaker. I think I have the peripherals allocated and wired correctly but wanted to run...
Hello,
I am testing a simple BLE application running in two different boards: nRF5340-DK and Fanstel BC40M. First test without MCU Boot, second test with MCU Boot. Same...
