Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I'm using an nrfx_timer event with k_poll_signal_raise to trigger a thread to perform an operation.
I've noticed around 900ms delay between when the signal is raised...
Hello!
We have a project where we are using the nRF52840 with the ADS7052 (an ADC) on the SPI bus. We are using Zephyr 4.1.0, but I guess its same same with nRF Connect...
Hello.
I have a setup in which two nrf52840_dk boards are communicating through BLE. I'm using Zephyr 4.1.99.
Under heavy traffic. the board which holds the 'central'...
Somehow a program I have running on a nrf52840-DK board will enable protection. This kind of screws up the small application I am testing because it seems to lock out the...
I have a LIS2DW12 accelerometer connected to nrf52840 SPIM3, and I am seeing an intermittent failure. In some instances while collecting accel data during a data ready interrupt...
Hi,
I believe the default application on Thingy91x uses LTE-m to connect, which is working fine. How do we make it use only nB-IoT?
For Thingy91, there is a guide
Getting...
Hi, We are using nrf Connect SDK 2.4.0 and have been looking through the NIST vulnerabilities databases. One of the vulnerabilities reported with the nrf5340 is a denial of...
Hello,
I am developing a board with the SIP nRF9151.
I'm designing the board with a shared antenna for both the GNSS and LTE signals (Ignion NN02-224).
For the antenna...
Hello Nordic team,
I would like to automatically patch the merged.hex file each time I build my project. I’ve attempted to use extra_post_build in CMakeLists.txt , but my...
I noticed that the product information of the nRF54L15 series kit supports 4Mbps, but I'm unsure how to verify it. Are there any relevant examples available? I have currently...
Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
Hello. I'm trying to improve the permit join-handling in our project. Right now we're simply hammering the zBoss stack with bdb_start_top_level_commissioning( ZB_BDB_NETWORK_STEERING...
Dear Nordic Support Team,
I am experiencing difficulties flashing firmware to my nRF52832 development board using VSCode with west flash , followed by J-Link...
We get the following assertion during startup if we include uart2 in the DTS.
*** Booting My Application v2.1.0-dev-ae1ee57f3906 *** *** Using nRF Connect SDK v3.0.1-9eb5615da66b...
Hello,
I posted this in Zephyr's repo at first, but was told to post it here since I am using NCS.
I am running cellular modem sample on nRF54L15 and have it interfaced...
