HI
I'm trying to use lpcom to detect when the battery voltage is dropping.
The configuration is as follows: 5V battery voltage output is reduced to 3.0V through LDO...
I am using an IMU sensor in sensor hub mode (LSM6DSV16X, LIS2MDL) with the FIFO interrupt interval set at 30 Hz. The data is sent over BLE. It works perfectly when using RTT...
Hello,
I am using the nrf5340 on some custom hardware, and I am using 3 LEDʻs and running them with the PWM0 peripheral to fade and blink and indicate states for the firmware...
Is nRF Mesh app support feature that send customize data/command to node? The goal is to transmit data from phone to node, where it will be processed and used to trigger actions...
Hello, I have a question about how to get commands generated from a client cluster in a coordinator. I am currently developing a hub to control and retrieve data from home...
I am trying to read the WHO AM I register of an ICM20948 over SPI with nRF52832, but I am getting incorrect values.
I have tried different SPI modes, but none of them work...
Hi,
I have a peripheral which is sending data to a central via the NUS service. Everything works as expected until the central is removed (e.g. power failure)
The problem...
Hi, My custom board with nRF52833-QIAA is using high Idle current than expected. I have tried 4 custom board and every time the current consumption is high. Although current...
Hi Team,
I have 1 nRF5340 Audio DK. With the steps mentioned in below links, I configured Json file to Headset and I'm able to achieve it.
Setup Details : Headset - nRF5340...
Hi Support team:
I'm using Zephyr cellular modem driver on the nRF5340 and set APN in prj.conf with 'CONFIG_MODEM_CELLULAR_APN="telenor.iot"' now. I need to set APN value...
Hi,
We are developing our own board with nrf6190. I already flash the chip with nrf9160dk_at_client_2024-03-13_af2b60d2 application and mfw_nrf9160_1.3.6 modem application...
I have the software installed and I am using the nRF52840DK with Ubuntu 22.04. The uart link is /dev/ttyACM0
When I start wireshark and do a capture on all advertising channels...
Hi,
I am working on custom board which has nrf9160 as modem and stm32 as host controller.
here I am used lwip stack on stm32 controller to get the IP address.
I have...
Hello,
when creating a multi-image build is it possible to select the optimization level for each image individually?
Below is an example of the issue I am facing currently...
Hi there, I need to collect modem logs to investigate LTE-M connectivity issues in specific countries. I have been using the command AT %X MODEMTRACE=1,2 to activate them...
We're developing an LwM2M application based on the lwm2m client sample with the goal of sending data to ThingsBoard as our main telemetry platform.
The Application in based...
Good night,
I am developing a Firmware for a nRF52840 created by RAKWireless RAK4631, with VSCode/Platformio/C++/FreeRTOS, and now I am changing the Architecture from a...
Hi Support Team,
I want to use an external flash(2M byte) to store the sensor data in a 'circular overwrite' way. I now tried it with the FCB(Flash Circular Buffer) on nRF5340...
Running the Ciphersuites sample code on the nRF9161 I get Connection Refused on all attempted ciphersuites. Including after adding the CONFIG_EXTENDED_CIPHERSUITE_LIST=y to...
Hello, I want to make periodically wake up nRF52840, performing some work (connecting to MQTT broker, sending some data) and after that going to low power mode. Then the nRF52840...
Hi,
we are working on a nrf52840 based device, which has an external mx25r16 flash (via SPI), having 3 partitions for: secondary-image, mcu-scatch-partition and application...
I am implementing SPI communication between the intanRHD2132 (ADC) and nRF52840.
I need to periodically send commands (READ, WRITE, etc.) to the intanRHD2132 (ADC). To achieve...