Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hi,
I have develop my firmware on on nRF51DK which has n51422 chip.
But my actual hardware has n51822 chip.
So my firmware is working on development board (nRF51DK...
Hi Guys
I've got a strange problem where a binary that works fine on a nRF51822 QFAC does not run on a QFAA
I know that the difference between these two devices is the...
I need to define a few constant arrays for IR implementation. Currently, I define them as
static uint16_t but it takes up a lot of SRAM space. How do I move them to program...
Hi,
I have a setup (in SD310.2.0.0) on nrf51422-qfaae0 in which I'm hoping to receive data on multiple ant channels from multiple networks, but I cant seem to understand...
HI,
with the new version of the bluetooth website, i can not find the link to overview the profile,service,characteristic and something else related to it.
thank you.
Hello,
I am working on a wearable device at the moment. To support iOS and Android at the same time, I have implemented ANCS and nRF UART on the circuit.
When working...
I successfully run "ble_app_hrs_c" on BLE_Central example at 38,400bps on the PCA10001 device.
My modification on PCA10001 board as follows;
cut out 32.768KHz X...
I want to store the max possible data on flash using pstorage , but I noticed that I have to increase the number of Maximum number of flash access commands PSTORAGE_CMD_QUEUE_SIZE...
Hello,
I have got a problem with use SPI. I get hard fault after call spi_master_open(), exactly when sd_nvic_ClearPendingIRQ function is call.
This situation is so specific...
link text from this post , i want to make code, when i press button,device goes into sleep mode.so i use this post's code in ble uart app. my code is here.
/* Copyright...
Hello all,
I am new to this domain.
Here is my case:
I am using the Atmel SAMA5D35-EK rev D. board. I was facing JTAG connectivity issues over J-Link.
My purpose is...
Hello!
I have Adafruit evaluation board with NRF8001 module and it works perfect.
I also tried to develop my own board with microcontroller unit and NRF 8001 module...
I have a few nRF51 dongles I wish to use with ANT+ for wireless mesh communication between some robots. I want to connect each to one ATmega 1284p and another Arduino Mega...
I'm using nrf25822, I flashed my firmware using DFU and I discovered the a memory regions starting from 0x0002A000 is written
this memory isn't written when I just use...
link text from this link i want to advertise for 10 second then i want to stop advertise for 20 second then again advertise for 10 second. i want this continuously. for that...
