Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi all,
I have ublox nina modules including your nrf52833 .
I downaloaded the ublox application here:
Release C209 AoA Tag v2.0.1 · u-blox/c209-aoa-tag
and opened...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Dear Staff,
we have some Ublox C2909 TAG based on your nRF52833 chip.We need to program them for an RTLS project.
In particular we need to:
customize the FW here ...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
Hello,
When the Ant stack want to transmit a packet while the BLE stack is using the radio, an event called EVENT_CHANNEL _COLLISION will be returned, is that...
Hello,
when the device NRF8001 starts Advertise, it sends out only one packet and unexpectedly terminates with a fatal hardware error in "ll_ctrl.s0.c" line 572. This happens...
Hi,
I'm trying to install Master Control Panel v.3.5.0 on Win7 64bit but I get the "Master Control Panel Setup Wizard Ended Prematurely" message. I have .NET Framework...
It would be very convenient to increase the output power of nRF51422/822/922 with at least 3-6 dB in order to get enough range. I'm currently not using nRF51422 for ANT, only...
with 1.16.0.3031 I cannot recover but I still can recover in Linux using a tweaked Makefile.posix
I don't remember this problem with previous version. Hence it must be...
I have tried to configure the nRF24A2 chipset in the asynchronous transmission mode by setting the bits in the extended field assignment. Unfortunately for some reason, it...
Hi,
I want to use 51822 to communication with 24l01,the 24l01 module is transmit temperature data, the 51822 is used to read the data from the 24l01.I set the parameters...
Hi,
I recently started on the nRF51822 Evaluation Kit and got the blinky code/example running. I then tried getting the Heart Rate application going but noticed when I...
Hi,
I want to use the nrf51822 to communicate withe the old module of 24l01p, in the module of 24l01p, the Address is
addrofch[0] = 0xe7;
addrofch[1] = 0x7e;
addrofch...
Hello,
I've been trying to get my TWI device working in conjunction with the BLE stack (i.e. s110 softdevice is enabled) on a nRF51822.
I found another thread with an...
Hi,
I want to use the 51822 to receive data that from the module of 24l01.the Address is
addrofch[0] = 0xe7;
addrofch[1] = 0x7e;
addrofch[2] = 0xe3;
addrofch[3] =...
Hi,
Can any one tell me, what will be the current taken by internal flash of Nordic for
write and read operation and what will be the max time nordic will take to write...
