Hi , am developing the st7789v_minimal_sample application using Nrf52840. after creating minimal application am facing some unrecognisable issue. which am stuck can you please...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Hi,
I am trying to use nfc_t4t_lib and I have some issues because processing incoming data takes some time (around 100 ms) and therefore sending the response occurs late...
I'm not sure if this is the right place for this question.
I'm using the Settings subsystem for the BLE name.
When BLE is initialized inside matter, settings_load is only...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
I try to compile SDK example following the tutorials ( devzone.nordicsemi.com/.../) ,
but i got some problems.
1.I can't finish setp of " Setting up a project for debugging...
Hello,
We are working on android UART service and NUS characteristic to receive notification and testing with the custom board with S130 stack acting as a peripheral.
...
Timer_interrupt.txt
Hi all, can anyone please help me in setup up the timer interrupt? I could only see the printing of "Entered 2". Kindly check on the attached text file...
Hi,
I developed a wire-less sensor based on 51822-BLE. I need a batch test method for the product.
My thought about the test is that connect the sensor to phones, and...
Hi support team,
I would like to know if the following behavior is a normal behavior:
My config: NRF51422 AAE0 + S310 V2.0
When I enable some inetrrupt like UART for...
I went through the documentation of nRF51-iOT-SDK v0.8.0 step by step. But
I could not cross-compile and build the kernel with 6LoWPAN on MAC OSX. I do not have a Windows...
I'm updating our bluetooth firmware and boot loader over the air from iOS and android devices. I've modified the nordic supplied update code (IOS-nRF-Toolbox project) to support...
I would like to use functions from components/libraries/mem_manager/mem_manager.c but it doesn't compile because of absense of sdk_config.h header file.
/home/gerbsh/sdk_11...
I'm concentrating on a work about connecting nrf51-dk device in the sensor node end implementing COAP server, ble enabled rapsberrypi and COAP client using Copper.
To check...
The PPI has been configured to transmit a message every time the timer triggers ( every 1ms).
I'm using IAR Embedded Workbench 7.40.3.8938 as my IDE .
When the system...
Hello all,
Our product based on nRF51 is on preproduction stage. We use both 16MHz and 32kHz external crystals.
The question is:
Is there any way to check programatically...
Dear all,
I do have troubles with the bandwidth of the nRF51822 contained in the Adafruit's Bluefruit LE SPI Friend module. The max. throughput I get is 213 B/s. I'm using...
After doing some DFU work - and it all went fine and dandy ...
I would like to go back to the plain old default bootloader that came with my nRF51 board. I don't seen any...
I'm using IAR IDE for the nordic development of NRF51822 (mdbt40). I'm able to run the example project which does not required soft device. Now i wanted to move further with...
Hi,
Is it possible to program the nRF51-Dongle through the usb, to correspond to Bluetooth content to change GPIO state. Then connect the dongle to an external power source...
