I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
I am using the 54l10 chip, and after compiling the project, I will receive a hex firmware and a zip update package. The bin firmware and hex firmware in this update package...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hi,
We have a hardware application that prevents us from using flow control to interface with external hardware. We require the NRF51822 to be able to buffer up to 256...
I have a working design on the nRF51822 Evaluation Kit, and I now need to port that into a module that sits on a custom board. Any recommendations for making this process...
Could someone can tell me what is the difference between BLE_ADVDATA_SHORT_NAME and BLE_ADVDATA_FULL_NAME? I tried BLE_ADVDATA_SHORT_NAME and BLE_ADVDATA_FULL_NAME
advertisement...
I am trying to figure out how interrupts are set up for say a sensor with an interrupt line which signals when new data is ready.
I am assuming you set up a GPIOTE somehow...
I have been looking at the NRF51822 for data logging sensor measurements from the ADC. Currently, I have run into some limitations with iOS and can only get approximately...
Hello,
Its me again.First of all I want to say thanks to HÅKON ALSETH, with his help I was able to work with hardware interrrupt. now I am facing another problem, I need...
want to FLASH upgrade FW in the nRF51822 though my application controller. Is C or C++ code available for this operation or can you deliver a protocol description how to setup...
Hello Everybody,
I am new to Nordic and Bluetooth. I see nrf51822a have BLE + Cortex MCU inbuilt and this suits best to my application.
I have some doubts regarding...
How do I use nRF51822DK without "nRFgo Starter Kit Motherboard"? I have read "nRF51822 Development Kit User Guide v1.2" and have no result how can I only use nRF51822DK hardware...
Dear All
i would like to use
nRF51822
nRF51422
i would like to use nordic product,
but so shame, too low basic knowledge for make program for embedded, edit library...
Hello,
I attached the schematic found in the manual for NRF8001, in the case of DC/DC converter enabled.
It shows that an external 32.768KHZ crystal is used, while in...
Hello, I have major problem trying to debug/run ble_app_hrs example. The thing is that when I enter debug mode the code is stuck here:
0x000001B4 4908 LDR r1,[pc,#32...
Based on nRF51822\Board\nrf6310\ble\ble_app_hids_mouse example,
Used hid consumer page function, like play/pause or volume+ or volume- ...etc function,
In nRF51822 device...
I can't seem to find the hex file to download into the PCA10000 in order to use it with the Master Control Panel. Where is this documented in the dev-kit documentation?