Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hello,
I checked Nordic website for layout of NRF8001 but i didn't find.
Please if some one can share a qualified RF-layout.
Help is appreciated.
Regards,
Hisham
from training document from Nordic company(see the attachments),it mentioned that we can add scan response .but i can not find any information in BLE_HRS demo.could you tell...
Hello,
I made a PWM with the TIMER2 of my nRF51822 (with the SoftDevice) and was working fine, till I read that I should not use the "NRF_PPI" functions and use the "sd_ppi_XXX...
I've got an nRF51822 development kit that I'm trying to get started on. I've gone to Kiel and downloaded uVision 4 (mdk472_a). I install it with all default settings and it...
Hi,
I add UART support using IRQ on the "ant_hrm_tx" example code.
and I'm sending packet of 4 bytes that contains: Delimiter,HeartRate,Battery,Delimiter
the frame...
Hi, I am trying to test my UART using some simple loopback test, and I have noticed that the service discovery command of BLE will occupy the CPU a quite long time. I am just...
I was unaware that the 'manufacturer data' in the advertising packets is limited to less than a full payload. However, whenever I set it to >6 the program "crashes".
...
When I use keil to download the software to the chip, there are two questions:
like attached.
2.NRFGO CAN'T SEE J-LINK LITE CORTEXM BOARD
Is there any way to solve...
We have recently moved to a new PCB which puts the nRF8001 on the layout instead of plugging into a nRF2741 development module. The nRF8001 connects to a TI Cortex-M4 Tiva...
Hi, we would like to create a kind of game using 2.4Ghz emitters . The 2.4Ghz USB Dongle emits and the mobile phone detects the frequency + embed unique ID/code so we confirm...
To be more detailed:
One of my ADC pins will be connected to another device that could be providing a voltage of about 3V, but through a 100 kohm resistor. (actually it...
Dear Nordic Developer Zone,
Since I have implemented a timer with interrupt in my application, the debug mode if the Keil IDE stops working when I try to restart the code...
Hello, I'm trying to develop with the nRF51822 Eval kit and GCC and Eclipse. I've been getting some strange behavior and errors lately. I'm not really sure how to describe...
