Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi, I'm looking for a solution can make a ble device communicates with multiple 2.4g devices at the same time , is 51882 qualified for this? or just by combining both nrf8001...
Hello,
I would like to use the fifo common library but i have an link error. I don't understand that because fifo_app.h is included and contain the functions...
...
Hi
We are using indication to send data to make sure master receive all the package.If we didn't
receive the confirm message,what should we do?Should we send it again in...
I'm guessing it is because the engine powering the site does not support it. But has it ever been considered?
I think it is a powerful way to engage users and build a community...
Hi,
I have two questions about nRF24LU1+.
Q1
Can i change nRF24LU1+ isocheonous endpoints(Endpoint 8 IN/OUT) to Endpoint 1 IN and Endpoint 2 OUT?
Q2
Can i use Endpoint...
Hi,
we’re a group of students at NTNU in Trondheim doing a project regarding bike and pedestrian registration. So far we want to make a solution based on iBeacon and Bluetooth...
Hello,
I am looking into the possibilities of implementing frequency hopping using the nRF24L01+ radio with an external Ti MSP430 microcontroller. I have read that it's predecessor...
Hi,
I want to realize the function of bond, I use "lib_aci_bond(180/* in seconds */, 0x0050 /* advertising interval 50ms*/);'\",.When I click the connect, it can connect...
In nrf51_sdk_v4_4_1_31827\nrf51822\Source\console\console.c,
#include "uart_legacy.h"
But there is no "uart_legacy.h" file in the SDK.
I have to modify to "app_uart...
I downloaded the source for the Android UART app, hoping to hack it into something I can use to test my gadget. But it's incomplete: it fails with the message:
Missing...
I have 3 short questions:
Does S120 support or will support swiching over BLE and Gazelle like S110 does?
Will be able in future to be connected to a BLE...
Hi,
If I want to send data(400Bytes) to client(phone),I must use sd_ble_gatts_hvx to notify client. Is it right?
Every time I notify 20bytes until the end, is it right...
Hi,
I understand that the available RAM on the nRD51822 is 16k. How much of that space is reserved for the transmission/ reception of BT packets?
Thanks,
David
