Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
I am working on a custom service using and nrf51822 device. SDK7.1 SD7.1
My security parameters are as follows:
#define SEC_PARAM_TIMEOUT 30 /**< Timeout for Pairing...
Hello,
I am running the UART app example in SDK 0.9.1 with the nRF52 and PCA 10036. I am using putty to send and receive messages, as well as the nRF UART v2.0 app for...
Hi,
I'm currently trying to determine the power consumption of my nrf51DK during different states of my program using an oscilloscope. To do so, I am using an external power...
We had been trying to use SD 7.0 with SDK 6.1.0, but realized our libraries were mixed up and not controlled very well, and we were experiencing occasional crashes where the...
Hello,
I'm looking to find a way to send a 32 bits number to the ledButtonDemo with the Master Control Panel (I have the Nordic dongle).
Indeed, I replace uint8_t led_state...
Hi,
I have a question regarding the NRF 52 boot sequence.
When we first receive it from Nordic, what are the boot options? Are there any other options to load a code on...
Hi,
I'd like to know how to set/alter passcode when pairing happens. I looked a few examples in Keil_v5\ARM\Pack\NordicSemiconductor\nRF_Examples\8.0.0\ble_peripheral but...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hi all,
If i have connect a band with my phone, then i let my band close to my notebook and let my notebook unlock.
Any suggestion about this?
Thanks in advance
Hello all,
I am working on the implementation of DFU OTA in our application, running on a custom board using the nRF51822-QFAC.
The tools that I am using are:
...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
[Update 8/15]
Here's the file for the main part of my code: sensors.c . The sensors_start() function at the bottom is where the while loop and the print statements are located...
I want to send data to my android phone from Nrf51822.My compiler is mbed I use redbearlab NRF51822 kit.For example,I want to see on my phone "hello world".
Mbed Program...
Hi,
I'm using S130 v1.0 softdevice and bootloader (single bank) from SDK v9.0.
When updating an application, I always get a CRC error at end of the upload. I generate...
