Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi,
currently trying to boot up mcuboot with nrf54l15 pm_static for both cpuapp and cpuapp_ns. Both files are included in the zip file.
I have already tried several configuartions...
Hi,
I'm using nRF9160DK with SDKs v3.0.0
I am trying to use A-GPS with nRFCloud REST. I used the location example and it works correctly. The documentation states that...
Hello,
I am new to modems and cellular domain.
We intend to design and build a cellular communication extension for an older product. And I eyed the nRF9151 for that....
Dear Nordic DevZone,
I'm encountering pairing issues with mobile devices and a nRF54 DevKit flashed with HCI over UART firmware. After initial pairing, deleting the bonding...
Hi,
I'm trying to get a modified version of the serial "NUS" service to work encrypted with Android 4.4 (API 19). Everything works fine on iOS, but with Android I get ofter...
hi,there
raspberry can ping6 pca10028, rasberry can receive udp packets from pca10028.
but how can i ping6 pca10028 from pc?
env: pca10028 + csr ble dongle + raspberry...
i'm confused of the relationship of wirepas and ant+,both claim to surpport mesh network and multihop.what's more confusing is that both are promoted by nordic.
I look up...
I find in the following example code that if I start my application from a powered-off to a powered-on condition and main() executes the code as shown, everything works fine...
Hi,
I do receive undefined HCI errors in my disconnection handler. I wait for the BLE_GAP_EVT_DISCONNECTED event and use the bleEvent->evt.gap_evt.params.disconnected.reason...
I've been reading through the documentation for pstorage but there's one term I don't understand
devzone.nordicsemi.com/.../a00131.html
What is the purpose of offset...
We are using two GPIOTE inputs and there is only 1 GPIOTE interrupt handler.
One of the GPIOTE input is from a power line chip that toggles @ 50 Hz rate. This GPIOTE input...
Hi Team,
I was trying dfu to load my application.
Edit #1
I have flashed softdevice.
Then I have compiled the example project 'dfu_dual_bank_ble_s110_pca10028...
I have an external temperature on my nRF51 DK. I would like to read the value of the temperature on my mobile device(Android).
I am able to read the temperature on the...
I would like to use the single shot timer and when the timeout handler is called, I would like to set up the same timer again with different interval this time. Do I have...
There seems to be a discrepancy between the 8.0.0 softdevice release notes and the product compatibility matrix. I would like to know if it is possible to use 8.0.0 softdevice...
Hi,
In my project, I need to periodically perform some jobs on the nRF51822 Beacon kit (sdk 7.1). For that, I think I need to use timers. However, I'm not sure how to do...
Hey everyone.,
I was trying to use nrf51822 as spi slave and just a heads up to know that i use Nrf51822 as master. I see that when chip select CS gets low SPI needs to acquire...
I've added a custom service and a few characteristics on the nRF51822. How can I access the current value stored in one of those characteristic outside of a BLE event occurring...
Hi,
I'm unable to run any application on nrf51 DK (Keil used). When I start debug (no matter what application I load), program always cycles between 2 instructions:
0x000006CC...
