fail to erase an nRF 5340 DK. Can't recognize the COM. But board is recognized as J-Link driver. Does anybody know why this happen? the log is as follows:
2025-06-16T07...
hello all,
I'm fairly new to nRF SDF and its build environment. I browsed a lot of posts but did not find the solution to what is probably a basic misconfiguration error...
I am using NCS 3.0.0 and I want to generate keys ... But the method I am using to generate keys is giving me this error Here is the code where it is returning error:
psa_set_key_usage_flags...
Is a common ground required when measuring current in current meter way?
Can externally supplied voltage exceed 5V? Will this cause inaccurate test results?
I'm working with nRF5340 and nRF Connect SDK 2.9.0, using sysbuild and Partition Manager for my project. I want to enable Zephyr's coredump feature and store dumps in internal...
I have a custom NRF9151 board with Windbond W25Q32JV flash, and some other peripherals connected. It also has GPS and LTE which I have tested and work. My UART console is...
Hi there, I am unable to install an SDK through VSCode while trying to take the steps outlined in the documentation. I have navigated to "Manage SDKs" under the "nRF Connect...
Is it possible to use the nRF51 dongle as a slave ?
I have a nRF51422 Eval board that I am planning to use as a central device. Can I use the nRF51 as a slave so that I...
Hello we have developed a few products which have required (costly) RF/RFPHY testing.
Is there a reference design that is qualified that can be used to avoid the RF/RFPHY...
Suppose a BLE central needs to get sensor data from 10 peripheral sensors. Given that there is a limit to the number of connections a BLE central can have, is it better for...
Has anyone managed to get this revision of the nrf8001 IC working?
i bought 280 of them and none of them seems to work as it should.
When i reset the chip i get no interrupt...
I tried to download softdevice 8.0 and the example code of SDK8.0
(\nRF_Examples\8.0.0\dfu\bootloader\pca10028\dual_bank_ble_s110\arm5)
to PCA10001.
First I Copied the...
I'm devloping application on nRf51 for that i'm using... SDK : nRF51_SDK_7.2.0_cf547b5 Tool chain : GNU tools arm Embedded [arm-none-eabi version 4.9.3] Dev Board : PCA10028...
Along with S110 BLE stack I programmed my application, which I managed to do without any conflict.
My application is not working properly and neither control is transfered...
how much time of keep level HIGH/LOW can make nRF51822 detected the HIGH/LOW level and generate an interrupt?
how width of impulse need to generate an interrupt?
Hi Team,
I was trying to load firmware to external board using nRF51-DK.
I have successfully programmed the boards many times and now when I am trying, LED (LD5) on nRF...
Hi all,
I downloaded the nrf51SDK_.8.0.0 from nordic site and tried to flash the new softdevice s110 but failed. I used an android application to flash it over the air...
Hi:
i use ble_app_uart project and want to change the UUID lenth(128 bit) to be 32 bit;but i change "nus_base_uuid" to be 4 byte and change "uuid128[16]" to be "uuid128[4...
Hi,
Does hardware that has already a Qualified design Listing (Bluetooth.org) requires re-testing of the RF-PHY ?
(refering to transmitter tests (i.e TRM-LE/CA/01/C (output...
Hi,
Im using a module NRF24L01 + LNA bought off ebay, connected it to msp430 via SPI interface. All spi communications are going solid, I manage to completely configure module...
