Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
The BLE Central tutorial (S130 based) does not connect to my peripheral. My peripheral connects fine to the Android MCP and the 128-bit service UUID is what I expect.
I...
I use nrfgo studio to program the hex file. but I have only 128kb of flash and the softdevice took 88kb which left less then 50kb. I have a hex file of 70kb
my question is...
hello.
I develope the using the Nrf51822, bootloader and application not using softdevice llbrary.
the procedure is that one mcu send the mrf51822 by uart. and mrf51822...
Now I have generated bootloader.hex used by /DFU/bootloader.
After programming bootloader.hex and s110_nrf51_8.0.0.hex,the device's name changed to DfuTarg.
But when I...
Hell,
Wich BT dongle I can use to dawnload data fro board with nRF51822 chip on it?
If thear is App. to use for comunication and dawnloading data from electronic board with...
Hi,
I am using nRF51422 with s130 soft device along with SDK v9.0. I am trying to read/write flash memory using pstorage module. I am using BLE nus service for data transfer...
each time I start my program (nrf51 device) I get an error code I save in flash to check it at next restart. I can read error code 0x20
is this a correct error code and what...
Hi,
I try to generate a PWM signal on PCA10040 with the nRF52832. To do that I copied the code from the Product Specification into my application, but nothing comes out....
Hi,
I made my prototype board using the nrf51822 chip. for this prototype i use an on-board connector + external programmer to flash the nrf51822 chip.
that's work...
I am looking ahead to the time when I will graduate from using the nRF52 development board to building a custom device with the SoC. The PCA10036 chip will obviously not be...
Hello,
I am almost finishing developement of a BLE module using nrf51822.
For mass production, I hope I can program Softdevice/Bootloader/Firmware to 10 nrf51822 using...
Hi
I want to receive and send a lot of data in a short time (connection Intervall is set to 20ms). And I get the App-Error 0x3004.
I found this definition for the error...
Hello,
I am currently trying to figure out a problem with my mesh. If I stop the event handling of one node, other nodes in the network will fail to send data from this...
PAN #9 in the nRF51822-PAN-v2.4 document provides a workaround for non-functional OUTINIT. This question and this one improve the workaround and state it's unnecessary in...
