Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
hello,
I am having some doubts regarding the connection handle. Will it be the same for both devices participating in a connection? I was trying to connect two devices, one...
A call to sd_ble_gatts_service_add(..) is returning fault code 0x3001. Looking at the NRF_ERROR #defines, this seems to mean "STK SVC handler is missing".
Can anyone shed...
Dear ladies and gentlemen,
I can't find this information anywhere. In the datasheet on page 519 - 521, I see that the decoupling capacitor C6 on pin 32 (DEC2) is not mounted...
Hi
Currently I have a device with the following details:
Ic Version - 2,
Variant - CE AA ,
Build Code - D0,
Hardware Id - 004d
I am using the softdevice s110_nrf51822_7...
I am trying to set up an environment based on CMSIS Packs. However, when using some components from nRF_Libraries, these lines get added to RTE_Components.h:
#define GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
I am working on nrf51 iot sdk. I have created a IPv6 tunnel in HE and is able to ping the gateway as follows:
root@raspberrypi:/home/pi# ping6 2001:xxx:18:xxx::1
PING...
Hi,
I already used the sd_ble_uuid_vs_add for adding my base UUID in the internal table and it return a valid uuid_type (in my specific case it's 0x06).
I need to add...
I am using SDK 9.0.0 and i am having a doubt in bsp.h.In this header file when gone through this part of the code
#if (LEDS_NUMBER > 0) && !defined(BSP_SIMPLE)
#define...
For nrf 51 - DK , I flashed s130_nrf51_1.0.0_API
and then using keil uvision I copied over ble_app_uart_s130_pca_10028 and
tried to compile the code,
The code failed...
Hi,
What is the maximum voltage a level than can be given as an input on a pin on nrf51-dk? I've measured VDD at 2.91V. Is it from VDD-0.3 to VDD? If yes, is there a way...
Now I am trying DFU via BLE, some times I can do it successfully and I can do it as long as i want to, but the other time it shows "Error(0x85) GATT error" message and whatever...
I'm testing the DFU as described in this link developer.nordicsemi.com/.../a00086.html
after reseting in DFU mode, when I start the device discovery, I only get empty packets...
