Hi There,
I am using a nRF52840DK board to experiment with NFC Tag technology.
I started with the "Writable_ndef" example inside the nRFConnect, and it works.
I wrote...
Where can I obtain the security certificates (e.g., client certificate/private key) needed for TLS authentication with nRF Cloud? - Are these generated during device onboarding...
I plan to use my own SIM card (not from Ibasis). Could you clarify how to register the device in nRF Cloud to enable A-GPS services? - Should I link the device’s IMEI or ICCID...
Hello, I am developing nRF5340, the project is pre-production. I am getting a issue with BLE power consumption, when I turned BLE on, the current is about 9uA. with BLE beacon...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi Nordic,
Could you please help me ! This is an urgent matter!
Based on this discussion , there is an error rate of actual baudrate comparing with the desired one.
...
Hello everyone,
I'm trying to use the new SDK 15.0.0 and the S140 soft device V6.0.0. I would like to use the LE CODED physical layer and set my TX output power, but when...
Why did the softdevice handler's API change?
sorry for a general question. I used SDK 13. and Now, I am porting my software to SDK 15. So, I have simple question. Why did...
My application is based of the UART example, I have a repeating app timer that fires every 5 min's to do some tasks, I also utilise single fire timers (initiated for events...
Ok, so I am using nRF52DK and trying to figure out to how to send up to 6 packets of data from custom service that sends 6 16bit values per packet. When I send one packet...
Hello,
We have a custom boards that powers a NRF52840 module from a 1.8v voltage regulator coming from a 3.6v battery. We also connected the positive pole of the battery...
I am new to embedded development. How do i physically connect the sensor to the board?
Is it possible without any additional equipment? What is important regarding pins...
Hi,
We want to certify a product embedded nRF51822 chip, with BAS and IAS defined by Bluetooth SIG.
Requesting SIG certification for it of a certification body, we were...
Hi all,
getting burnt out from searching the fourms and finding dead ends or outdated answers so just posting a question quickly.
Somewhere along the line my nrf51DK has...
I am working on a product based on the nRF52832 (using the Rigado BMD-300 module) which is basically a data logger with a BLE connection for offload. I am running FreeRTOS...
Hello,
We have a custom board based on nRF52832.
there is 1 LED on P0.29:
#define LED_1 29
First I initialize the GPIO:
nrf_gpio_cfg_output(LED_1); // this lights...
When I complie this SDK using keil5, I got this error "Error #544: Required Software Pack 'NordicSemiconductor.nRF_DeviceFamilyPack.8.16.0' is not installed'" How can I get...
red-contrib-nordic-thingy
Always getting "no thingy found" error from node-red in ubuntu. But i am able to use gatttool and able to get notifications from thingy on button...
I've noticed following line in SDK14.1 release notes:
`
Fixed a bug where nrf_log could crash when heavily loaded.
`
I'm using SDK13.1 in my current project...
I've recently jumped to nrf5 sdk v15.0 from v12.3 and met a problem in setting up a custom ble service. Actually the service itself is visible via nrfConnect andorid app,...