H ello Nordic team,
I'v found a bug on mqtt sample (using both ncs 3.0.0 and 2.6.1).
Description
Settings CONFIG_MQTT_SAMPLE_TRANSPORT_CLIENT_ID and trying to connect...
Hello Team,
I have flashed the bap_unicast_server bluetooth sample on my nRF5340 Audio DK. No build or flash errors. When I connect to my phone it connects properly. I'm...
I'm working on a project involving a USB dongle based on the nRF52840 SDK-2.9.1, which needs to communicate with a sensor (also an nRF52840) and transmit data via USB to PC...
Hello Nordic team, For the ( POC), I configured ADC channel 1 and interfaced a potentiometer to pin P1.14. The ADC was set up accordingly to read raw value from the potentiometer...
Hello, I have been going through the DFU and FOTA lesson in the Nordic intermediate course. I see that there is a FOTA support for a scenario in which we want to update a...
This sounds like a stupid question... but I would like to clarify if this pin is an input or output. I think it's power in but want to make 100% sure as I'm spinning a PCB...
We are experiencing some ESB link failures on the receiver end of our system: nrf54L15. After minutes to hours of use the receiver will stop getting data (we know the transmitter...
1st problem:
There are some failed case when i run \v2.9.1\modules\bsim_hw_models\nrf_hw_models\tests\zephyr_apps\54_aar_ccm_ecb\src\test_ccm.c
2nd problem:
If I...
Dear Nordic Teams :
I find the NFC current and find the current is quite large in the datasheet version 0.8. The value is much bigger than nRF52840. Is it correct?
Hello,
I am planning on using the WLCSP version of the nRF52840 chip on a PCB design. ( nRF52840 - Bluetooth 5.3 SoC - nordicsemi.com )
Is it possible to program the nRF52840...
Hello,
I am looking to use multiple PPK2 to measure current across 2+ voltage rails at the same time. Is there a way to connect 2+ PPK2 and synchronize the data from the...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Hello,
Hopefully this will be a quick(ish) one since I think I found the answer, but just need confirmation.
To preface (My setup):
nRF9151DK
Modem firmware: mfw_nrf91x1_2...
I'm developing a small IoT device that needs to retrieve and transmit its location upon pressing a button. While testing the modem using AT commands, I can consistently retrieve...
Bit baffled by this one, I assume it's related to the attempted nRF SDK Intellisense magic: We do have a monorepo for various controller projects that includes two zephyr...
I have an nRF5340 DK that exhibits unusual power behavior. When I plug in the IMCU USB port (USB connected to onboard debugger), the board briefly flashes all LEDs , including...
Our design has an nRF5340 with RV3028C7 to provide the 32 kHz clock via P0.00.
If I configure P0.00 as a digital input, I can see the pin toggling.
However, if I use the...
After I updated to v2024.11.22 of the nRF Connect For VS Code I can no longer get the option: "nrf-connect.debugging.flash": false to work. It keeps flashing the device before...
Hello,
I've been working on a project involving an IMU and bluetooth for a while, and had been using the IMU (LSM6DSO) on polling mode. Unfortunately, I found out that I...
Has anyone else had problems with adding build configurations for workspace applications using the VSCode GUI interface? Initially I clone the repo using CLI-based west commands...
