Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
I'm working on a project where I want to integrate AoA into the DS TWR templates provided in the DW3000 api. My hardware is made up of the QM33120WDK1 Ultra-Wideband (UWB...
As subject, I want to build a NCS demo at console, but always report error:
C:\ncs\v3.0.0-rc1\zephyr\samples\basic\blinky>west build -b nrf52840dk/nrf52840 -- west build...
I have a project where we did not populate the external oscillator for our custom board which has an nrf5340 on it. I did most of my BLE testing on the nrf5340 devkit and...
servo uses pwm0 device, channel 1 in DTS file.
But in its pinctrl file, GPIO P0.13 uses PWM_OUT0 which is channel 0.
It should be changed to " psels = < NRF_PSEL ( PWM_OUT1...
Hi, Can you please help in connecting the nrf52840 DK with CMW500 and to measure the RF power at different levels of nrf. (For example, at 8dBm, 4dBm, 0dBm, -40dBm). In this...
Hi,
I'm using the nRF54L15 DK (non-secure, NCS v2.9.1) to generate a 100 kHz PWM on a GPIO with TIMER00 (128 MHz, 1280 ticks, 2.5%–20% duty, 32–256 ticks). GPIOTE, DPPI...
I am developing using the nRF5340DK with Segger v5.68 and SDK within toolchain v1.9.1. My project works perfectly on my old PC, but after moving to a new PC with the exact...
Hello, I would like to implement a simple RSSI-based distance measurement function using the Periodic Advertising Samples（periodic_adv & periodic_sync）. In the scan callback...
I don't know who's in charge of Dev Academy, but the nRF Connect SDK Intermediate Lesson 9 -- Bootloaderse and DFU/FOTA section looks like it was written as a back burner...
Hello, I am trying to save some sensor data based on my current state of the device. I want to log IMU data and timestamp into my external flash (MX25R64) with littlefs file...
I am using a custom board with an nRF52840. For OTA updates, I’m using SDK 17.1.0 based on the sample codes:
Bootloader : secure_bootloader
Application : A custom...
I am developing with thingy53. I would like to enable BLE function, MCUboot and littlefs file system at the same time. I am using SDK and toolchain v2.7.0 and sysbuild as...
The samples "nrfx_gppi/fork" and "nrfx_gppi/one_to_one" are both broken and fail to compile. I have confirmed this for NCS 2.8.0 and 2.9.1 on Linux, and 2.8.0 on Windows....
Dear nordic team,
even if enabled for mcuboot via CONFIG_WATCHDOG / CONFIG_BOOT_WATCHDOG_FEED, our device performs a reset when swapping the image. More precisely: when...
