I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Hi! I'm testing the application with the custom Battery pofile I generated with nPM PowerUP app. During testing I found the issue with the SOC value calcultation depending...
Hi Nordic Team,
I am planning to develop a SmokeCo device using the nRF54L15. I tested the example code of Smoke-Co from nrf-sdk with nRF54L15-DK and that working correctly...
Is there a trick to getting nrf_dm to compile on the nrf54l15?
I've installed v2.9.1
Command I normally use (nrf52840):
west build -b nrf52840dk_nrf52840 -d build_nrf52840dk_nrf52840...
Hello,
I am using the following device and development kit:
Device: NORA-B106-00B (nRF5340)
nRF Connect SDK: 2.0.2
Currently, I am trying to use GPIOTE PORT...
I've been trying to run the example Mesh/Chat on NRF7002DK, and the terminal print <err> bt_mesh_pb_adv: Failed enabling advertiser and <err> bt_mesh_pb_gatt: Failed enabling...
After using the backup v2.9.0 project to overwrite the original project, I encountered the following issues during compilation： How to solve it? Using Windows not Linux. Thank...
Hi Devzone
We found that the NRF54L dk will stuck if add systemView function into the bluetooth sample project
we add below config into peripheral_uart/peripheral_lbs...
i brought Power profiler kit II deveice and try to measure current on it.
i couldnt get proper measurement can you please help me on this? it is giving some random value...
Hi!
I have an NRF9151LACA AEA device and I'm trying to get it to work. Got the IMEI and the device successfully connects to cellular network.
However, I can't get HTTPS...
I am developing an app for a custom nRF52840 board. I am using the latest version of the nRF Connect SDK (2.9.1) and have enabled OTA DFU in firmware using MCUboot and sysbuild...
Dear Nordic Support Team,
I am working with the nRF52840 in a multi-protocol setup and would like to clarify the feasibility of the following configuration:
Running Thread...
Hey,
we're currently testing our devices with Modem FW 1.3.4 / nRF Connect SDK 2.2.0 and have observed the following error:
LTE-M
Connection was successful before...
Hello Team,
I am using nrf54l15 dk for the development. In this, I am using k_sleep to put the device in system-on sleep mode. Using this, I have achieved the sleep current...
Hi,
I need to use AES CBC 256 encryption/decryption on nrf52840 but since its cyrpto cell only supports AES 128, I tried using mbedtls to do AES 256 encryption. It works...
