Hi Sirs
We are planning to use the nRF54LM20A/B together with the nRF21540 FEM in our design, and we have a few technical questions regarding TX power control and FEM...
Hi Nordic Support Team,
We are currently evaluating the nRF54L05 DFU single-slot sample in NCS v3.3.0.
Our question is: Is it technically possible to configure the single...
Hi,
I'm using the published nRF54L15 DK hardware files and noticed something that I don't understand.
On the nPM1300 section of the schematic and PCB:
Pin 20 ( VSYS...
we are developing solutions with PMIC type=PM1300, we eager to know the internal LDOs PSRR.
i have read 171 page of PM1300 datasheet, but cannot find PSRR data or the PSRR...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi,
I am developing a react native app with the iOS and Android NRF mesh lbrary. In this app I am handling connection, data receiving on characteristic and sending on...
Hi
I'm evaluating using the nRF52805 for an application that would use BLE but require almost no BLE functionality. Only the ability to periodically wake up and scan is...
Greetings. We are using the zigbee/shell sample in order to verify the connectivity of some other devices running the zigbee stack. While the shell sample had no issues in...
Hello,
I want to create a Matter network using my nRF5340 DK board, as Matter accessory, and my RaspberryPI, as controller (CHIP Tool controller). I'm using as well nRF...
1.SDK:SDK17.1
2.IAR V9.2
3.
static float inv_sqrt(float x) { float xhalf = 0.5f * x; int i = *(int *)&x;
i = 0x5f375a86 - (i >> 1); // this is magic. x = *(float ...
Hello,
I am developing a door lock system. Where in final product door lock will be controlled and monitored by BLE+Zigbee. So far I have complete success of controlling...
Hi, I'm developing an application using UARTE to reading response from Module Sim. The content response from Module Sim has 495 characters. When I debug, I only read some...
Hi.
I am developing nRF52832 and ST7789.
I'm trying to print out the text, but it's not working properly.
The nrf_gfx_screen_fill() function works fine.
When I proceed...
Hi
I can't set CommonName in the attributes list while generating a private key, it gives an error:
Omitting CN it works fine:
What am I doing wrong?
Thanks...
Hi
I have a question concerning AOA.
I have already make a tx (with nrf52833) and a rx (nrf52833 too) and i succeed to receive the CTE and the IQ sampling with the antenna...
Hello ,
my team and i we are trying to set a communication by UART between two nrf52840 µC , with one of the µC we have done a communication with a nucleo board which supports...
Hello all,
I have made a simple app that runs in loop on the nRF52DK, in general it reads data from the sensor via twi and turns on the leds ...
When the program is run...
Hi, i am developing Zigbee window covering device on nrf connect sdk 1.9.1v which has 2 endpoints, but i am face issue when zigbee command is received and
device_interface_cb...
I have Ebyte’s E73-2G4M08S1C (nrf52840-QIAAC0/ aQFN73 module) where P0.19, P0.21 and P0.23 are not wired out :(
So, my question is which other pins could use / not use instead...
