Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
We are using NRF52832 based Module in our design. Currently BLE Services & characteristics used in our firmware: 1. Custom Service characteristic 1: 37 Bytes characteristic...
Hi,
I understand that BLE Logical Link Control and Adaptation Layer Protocol is responsible for protocol multiplexing capability.
Can you please explain what kind of protocol...
Hey,
when i call:
otLinkSetChannel(OTInstance, ThreadChannelToUse);
from the very beginning of the programm:
void main(void) { int ret; ret = InitLEDs(); InitTemperatureMeasurement...
We are using nrf5340-dk to communicate with nrf5340 custom board and trying to search for the other sensors' addresses. There is secure mode and unsecure mode CPU. Which mode...
Hi.
My first attempt to get SAADC to work was:
NRF_SAADC->INTENSET = (SAADC_INTEN_RESULTDONE_Enabled << SAADC_INTEN_RESULTDONE_Pos) | //A result is ready to get transferred...
Hi,
Can I connect a 3.7V Li ion battery to the dongle VBUS keeping the SB1 and SB2 configurations as default?
Would this 3.7V applied to IC's VBUS pin cause any issue...
I want to view extended advertising, auxiliary advertising , LE coded data.
i had installed nrf sniffer app wireshark but it doesnt display this.
Ellysis bluetooth tracker...
Hello,
I am working on NRF52805.
I am able to debug my program with J-link using SEGGER.
However, when I try to download the program it seems like it is not running...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0) as central.
Is it possible to change the Tx Power while connected to the device? I made it possible to change...
Hi,
I am migrating my project from SDK15 to SDK 17.0.2. I am using NRF52840 development kit and using s140 softdevice for bluetooth services. When I load the softdevice...
Hello.
I'm trying to make very simple iBeacon. So, I modified an example of 'ble_app_beacon'.
Things what I have done are below
1. wrote J-Link OB-SAM3U128-V2-NordicSemi...
Dear supporters team,
I would like to create a new project, It has a feature scan BLE peripherals and print name of peripherals
Could you help me suggest step by step...
HI Devzone
i am using <NCS_SOURCE_FOLDER>\nrf\samples\nfc\tag_reader\ to do the test. on NCS1.5.1
i am trying to add a customize compatible properties in device tree....
