I try to get the one button sample to work. There were several details missing to be able to compile and run this sample, which was very frustrating. After editing/updating...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
I am trying to connect and read the data of the MIO Fuse heart rate band. It is designed as per the Bluetooth SIG specifications i.e heart rate service UUID is 180D and the...
Hi,
A project I'm working on can be seen as a collector of data from many different sources. To keep I an overview I've decided to use C++ objects rather than C (in other...
Hello,
I'm using nRF52833, s140, pca10100.
I looked at the code 'nrfx_saadc.c' to uninit SAADC.
The file contains two types of code, with or without the definition...
Hi,
One of our unit started to systematically report DNS_EAI_SYSTEM (-11) when calling getaddrinfo(). In a attempt to get more info about the error, I added errno to the...
Hi experts
I am trying to play a little with BLE HID keyboard example supplied by nordic
I see that there is an array of 5 characters "hello" + "enterkey press" which is...
Hello There,
I want use I2C in nRF9160 for getting MPU6050 or MPU9250 data in it,
I try this Example with change overlay file in it
SDK 1.5.1 and also try with 1.40...
I am trying to send data obtained from my sensor (calculating with twi scanner example ) via BLE using the ble_nus_data_send function. I just tried to send this data via UART...
Hi,
The eddystone example enter to connectable mode by press a button, but our customer don't want to press button one by one, they hope the beacon can advertise eddystone...
Custom nRF52 device uses SPI interface for external flash, so in order to read/write to external flash would need a RAM loaded firmware to keep code in internal flash untouched...
Hello,
How can I have two or more temperature probes reporting using the ZCL library?
Imagine that I want to have a device that measures for instance two temperatures...
Hi,
I am trying to measure the current of a custom board using PPK board, My custom board takes 5 Volt input supply but PPK board has a 1.8-3.6 Volt external power supply...
I am trying to modify the nRF52840dk_nrf52840 spi_flash sample, ncs/zephyr/samples/drivers/spi_flash , to use dual QSPI.
Following is my device tree configuration:
I...
I am able to pair a peripheral device using advertising 16bit UUID to the Central Device(nRF52840-DK board).
Also I am able to read the Battery level service and Device...
Hi, I have successfully achieved the OTA DFU function on nRF52805. This is what I can see now:
Step 1) I can see the Nordic_Buttonless BLE signal. After connection, there...
When using the nordic power profiler for the nrf52840, it gives the "idle" current as 2.7uA. Presumably this is the deep sleep current, but it seems like this number doesnt...
