Hi Nordic teams,
I am working on integrating single-slot DFU for the nRF54H20 based on the throughput example. However, I noticed a difference in how the Bluetooth controller...
In the absence of a QGAA reference, is there anything to be aware of when designing a QGAA board?
For example, with the nRF52840, the WLCSP and QFN references used different...
Hi Nordic
I am wondering whether one device can connect to two Bluetooth devices at the same time and independently control the TX power to communicate with the two devices...
I’m using the RADIO peripheral for BLE 1M connection-event RX→TX turnaround.
Current flow:
1. RADIO receives a data PDU. 2. RADIO reaches END/PHYEND and disables. 3. In...
nrf sdk 2.9.2
I wanted to stop Bluetooth activity, so I used `bt_disable`, but a kernel panic occurred.
So I create a simple example to try this function, I still get...
Hi,
When starting nRF Connect for VS Code, SDK v3.3.0, the message Unable to resolve configuration with compilerPath: "C:\ncs\toolchains\fd21892d0f\opt\zephyr-sdk\arm-zephyr...
I have recently purchased nRF52840 dongle which I wanted to use as a ZigBee sniffer. I bought it on AliExpress and it supposed to be original Nordic board, but it turned out...
in sample ,prj.conf had configure ble device name using below define :
CONFIG_BT_DEVICE_NAME="Nordic_UART_Service" ,
in hci_core.c function bt_enable() use set_bt_name...
Hi Nordic,
In this question: https://devzone.nordicsemi.com/f/nordic-q-a/56529/how-to-check-or-read-the-list-of-bonded-device-from-nrf52832 It was discussed to update...
Is it possible to use both Zigbee & BLE MESH at same time?
Actually we are planning to use NRF52840 for our next project. In which BLE MESH will be used for BLE mesh device...
Hello,
I am using NCS v1.5.0 and my application runs in non-secure mode, and uses a custom SPM. Initially all build and ran correctly, and the SPM fit in a 32 KB partition...
Hi Dev team,
I am running an application using Thingy91 along with MQTT.
I am having a simple logic of storing data for a while and then sending it out through MQTT. For...
Hello,
I've been testing 802.15.4 single PHY (no softdevice) and analyzing packets on a TI CC2531, just to check interoperability. Things seem to work well when the packet...
Hello Everyone.
I am a newbie in NRF52840 development. I have one NRF52840 device as a central device and many peripherals are getting connected to it (Max 6). Lets say...
I am currently using the 17.0.2 SDK to develop some code on the nrf52832 which involves streaming data via SPI to an external flash. I need to stream this data at a ~50KHz...
hello, I have a question need you help.
SDK:nRF5_SDK_14.2.0
MCU:nRF52810
My product is used as a central.
When the voltage of the battery supplying the product is...
I am trying to develop an application using ANT on the 52805, I have purchased the nRF52 DK as this was the recommended development kit for this device but there seems no...
I have a design that uses the NRF52810 as well as NRF9160.
For safety reasons, it must have a fuse that is about 1 ohm into the system. I'm seeing an issue after an input...
Hi, Nordic.
Our customer employs nRF51802 in their product.
They use BLE and 2.4GHz proprietary at the same time. They want to know the switch speed between the two protocol...
Howdy DevZone! I'm brand new to BLE, and have some beginner questions on the best way to architect a project for ultra-low power consumption.
Here's what I want to make...
