Hi,
I am trying to configure an Xiao Seeed Studio nrf54l15 sense to transmit pre-processed sensor data via BLE extended advertisements. As the payload is more than 251 bytes...
In this post mentioned: "Maximum theoretical peak data rate is 3.4 Mbps when transmission is scheduled into packets of 4 slots using MCS4, and these 4 slot packets are transmitted...
I want to use a new source LF clock to raise the precision from +-250ppm to around +-20ppm. I already have an oscillator mounted in my PCB, so I want to use it for BLE. I...
Hi,
I would like to know if its possible to run Azure FOTA functionality w/o using Partition Manager (aka `SB_CONFIG_PARTITION_MANAGER=n`) ?
Trying to build this gets...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
Hi everyone,
I’m trying to program/recover a custom board with an nRF52840 Fanstel module using a Nordic nRF52840 DK as the programmer. The board is powered from a 4.2 V...
In the absence of a QGAA reference, is there anything to be aware of when designing a QGAA board?
For example, with the nRF52840, the WLCSP and QFN references used different...
Hello DevZone,
I am developing on nRF5340-DK v0.11.0, with nrfx v2.2.0 running with mbed Cordio, compiled with GNU make 4.3. The end goal is to make a Bootloader for the...
Hello everybody. I need to rotate servo and check adc on potentiometer to stop it if something is blocking the shaft.
I need to change servo position step by step and check...
i re-uzip NCS1.5.0 ,using SEGGER Embedded studio or using bash.exe to creat a sample project ,and can not creat .the problem is
CMake Error at D:/v1.5.0/zephyr/cmake/zephyr_module...
Hi Nordic,
Aquick question with respect to the Thingy91. As part of our development, I am looking to the Thingy91 as a reference. In the Thingy91 design, it appears that...
Hi, I'm new to C language. I copied and pasted nordic example TWI codes to my self-defined SDP31.c file. And declared some of the functions in SDP31.h.
After clean and rebuild...
Hi
In other toolchain with GCC it is possibility to move some variable to a non initialiseed section
__attribute__((section(".non_init"))) int buffer[1000U];
When I...
Hello,
I cannot receive the email about SUPL client library download link.
The email is the same as my devzone account.
I have checked everything in my email subscription...
Hi
i would like to how to properly set an authorization on write, i am using sdk 17. please explain all proper value of "ble_gatts_rw_authorize_reply_params_t " for write...
use ncs1.5.0 and sample peripheral_uart ,a board with nrf5340 . load app core hex and net core hex in nrf5340, i use a andriod app can connect nrf5340 through ble.
but below...
Hello
I am trying to install CMSIS on nrf Connect SDK.
I followed the instructions to modify the .xml file and point to the folder location of the .jar file in "Tools...
Can the pairing code be extracted from memory via JLink during production in order to print a pair code decal for a product without a display?
I know it shows up on the...
Hello devs,
I found this thread: https://devzone.nordicsemi.com/f/nordic-q-a/48928/radio_test-example-code-run-on-nrf52811 where exist it for the sdk 15.3
Is there something...
Because of my forced downgrade from Win7 to Win10, I can no longer build an older project under VS, so I am porting it to SES, the "approved solution" development environment...
Hello. Using SDK16 on my NRF52840 board I'm stuck here on my product development - trying to make my device have longer "sleep" battery life. when I call a simple function...
I'm trying to implement OTA update via BLE on my nrf52dk using Zephyr. I'm following this configuration guide to implement the FOTA in my project. However, when connecting...
