Hello, im trying to create OTA system for nrf54l15 and currently running into issue with the key provisioning
Device: nRF54L15 based custom board ( nrf54l15/nrf54l15...
While building the program I get this error message: "DT_N_NODELABEL_cpucell_cpuapp_ipc_shm_trace_REG_IDX_0_VAL_ADDRESSU" As far as I can tell, this error message is releated...
Hi Nordic team,
I am currently researching Bluetooth Channel Sounding, where I have setup two nrf54LM20-DK as intiaitor and reflector respectively.
I am using NCS 3.3...
Hi:
I use sdk ncs3.3.0 and nrf54lm20dk.
Failed to return using AA dfu_target_init.
OTA firmware is zephyr.signed.bin.
I: DFU header I: 3d b8 f3 96 00 00 00 00...
Hello,
I've been asked to create a new ticket for this. It follows on from
@ Erlend Isachsen asked:
So before marking this problem as resolved, it would be nice to be...
I am developing on the nrf9151 with SDK v3.4.0.
The device I am developing will be moving trough all of europe . My goal is to speed up the `AT+CFUN=1` conenction part of...
Hi,
I found that the startup of the modem (init and connect) is much faster after it has stored some initial information ( I think band-data and so on). This only happens...
Hi,
I have two nRF52 DK boards which i bought one is 2 years old and another 1 year old.. Past week both DK boards are failed to connect with the computers but the power...
We have the following setup:
- nRF52832 XXAA
- SDK 6.0
- S132
I have attempted to add a memory guard into the location preceding the application RAM data block start...
Despite following the procedure listed below, no text appears on the OLED display, despite the driver being able to communicate with the device.
I am using nRF Connect SDK...
I am looking to get some clarification on the QFN94 footprint of the nRF5340. There are four corner pads and they do not appear in the mechanical specifiications section 9...
Hi,
When looking at the reference schematics and reference layout of nRF5340 I notice that pins A25, B12, B26, G1, H2 and J31 are grounded:
Figure 1. Circuit configuration...
Hi, with my nrf9160 I need to send a gps location every 3 sec to azure, so I combined the agps and the azure iot hub sample. It's working pretty good but 10 sec as a periodic...
Hi, I doing PCBA prototype. And I found part number nRF5340-QKAA-R and NRF5340-QKAA-AB0-R7 in the website. In my understanding. The NRF5340-QKAA-AB is a sample engineering...
Hi,
I want to used NRF5340-DK for my BLE receiver evaluation I find LNA (NRF21540-DB) which is suitable to use with NRF5340-DK.
But I could not find this available in...
I am just beginning with the dev kit I bought in December. The box has a URL: nordicsemi.com/start52840dk
This is not helpful. The only thing I find there is a PDF - apparently...
hello,
i am using sdk 17 with ses v5.20 i have customised board consists of Decawave 1000 , Nrf52832 and accelarometer i want to compile and run both initiator and responder...
Please tell me about RBP CONF of UICR. Q1. What is the purpose of UICR's RBPCONF (read-back protection)? What kind of protection is it? Q2. What changes when RBPCONF (read...
I'm having problem connecting my thing:91 to the nrfcloud. When im trying to connect im getting "Troubleshoot nRF Code 40412". One of the reasons could be "before attempting...
Is there any way to run the TIMER peripherals off of the 32khz clock? We need to generate a 1khz PWM while the micro is asleep, and we really need to be able to shut down...
