Hi There,
I am currently developing an LTE-M application on nrf9151 using ncs v3.2.1, the device is a MQTT client that publishes telemetry periodically every 3 minutes,...
Hello Nordic Team,
I am working on an nRF52833 project using nRF5 SDK 17.1.0 with Secure DFU Bootloader.
Environment:
MCU: nRF52833
SDK: nRF5 SDK 17.1.0
SoftDevice...
Hello Nordic Team,
I am currently working with the nPM1300 EK together with the nRF54L15 platform and a custom 40 mAh Li-Po battery.
I am facing an issue while configuring...
i2c_write_read() returns -5 (EIO) immediately when writing register 0x01 to the sensor. Logic analyzer confirms the sensor clock-stretches SCL for ~14µs+ after receiving the...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi All,
Recently I have been working on nrf9160dk board. The use case is to have nrf9160 work as a serial LTE modem with GPS functionality. I have the following link https...
Hi,
I have implemented my own Vendor model, using the light switch client/server as a starting point. The model allows to send byte arrays. Since I have used the generic...
I am using SDK v16, SEGGER to program on my nrf52832 SOC for our project. I need to save a few variables to the flash memory. These variables will hold the status of the device...
Hello,
we are using SDK version 15.3 and mesh SDK version 3.2.0, on a nRF52840 DK board using the Segger Embedded Studio IDE version 4.52 (64-bit).
Our goal is to add...
Hello,
I followed this tutorial in order to familiarise with the code and understand better what is going on. Now, my question is the following, regarding challenge 2 :...
Hi,
I'm using latest master branch of nRF Connect SDK and pre-released modem FW 1.1.2 which is including ANT->AUX switching. I'm developing a firmware for a custom board...
Hello,
I notice that Thread examples with Softdevice (nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b) works fine for a PCA10056 but not on a PCA10059. When I had tried...
I am using nrf52832. I have one led connected to the gpio 25 through the active low condition.
i am trying to configure gpio 25 using this " nrf_gpio_cfg_pin_output(25);...
Hi, what is the impedance of the nRFM9160 GSM antenna?
I'm asking because I'm in the process of verifying the tuning on an antenna + LNA circuit. We will most likely tune...
I am using nrf52832. I am making custom board file .I am little bit confused which function are used for set the pin as output or input.
__STATIC_INLINE void nrf_gpio_cfg_output...
Hi All,
from below post, I found that in SDK11, bootloader code uses NRF_UICR->CUSTOMER[0] register for device type and revision verification so application should not use...
Hi
This is Joe. I would like to ask questions about implementing BLE bonding.
SDK: 16.0.0 (nRF5SDK160098a08e2)
Projects: The base project I start with is NUS example...
Hello,
I am trying to develop BLE custom board. It's my first time dealing with Nordic MCUs and RF. I want to understand if I am doing it all correct. Here is a piece of...
Hi,
In the I2C communication,the nRF52840 SoC is master, the sensor SCD 30 is slave. The sensor SCD 30 needs the clock stretching period, the period time is 12ms or 150ms...
Hello,
I have a general question for you.
When we develop an application from one of your examples and then you put online a new version of your SDK, do you have any advice...
