Hi
Have you done any benchmarking to estimate the difference in power consumption when comparing the nRF9151 in NTN mode vs LTE-M?
In particular I am curious if NTN has...
I requested a SUPL client license as I want to evaluate the AGNSS feature, but it got declined for some reason. And when I try requesting another one, nothing happens. Does...
Hello.
When I ran the NCS SBOM command using VS Code, the following error occurred, and the file could not be generated.
I would appreciate it if you could tell me how...
I am using nRF Connect SDK 3.4.1 on three nRF54L15 devices:
A ───────── B ───────── C
A–B: A central / CS initiator
B peripheral / CS reflector
B–C: B central / CS initiator...
Hello,
I cannot download many of the applications offered in the desktop. I am trying to use the evaluation board for the nRF54L15 offered by ezurio (BL54Lu) and cannot...
Setup
- Programmer: nRF54LM20 DK (PCA10184), debug out header P13 to an external board over a 10-pin ribbon under 10 cm, SWD0_SELECT grounded on the target side. The DK...
I created software and flashed successfully to the nRF54L15-DK. It is to toggle an LED on and off on P2.09.
#include <zephyr/kernel.h>
#include <hal/nrf_gpio.h>
...
hi all:
NRFSDK_16. I want to get timestamp from rtc,but my device need run with low power,so when the device in idle mode(no user use),will put it in system off mode.
...
Hi, Nordic,
I have the follow questions in the nRF5_SDK_17.0.0_9d13099
1. Why in the Demo ble_app_multirole_lesc remove the BLE_GAP_EVT_LESC_DHKEY_REQUEST's process as...
Like --insecure option in the curl command, i want to skip certificate validation when make a https connection to server, so i have checked all http files in zephyr and there...
Hi everyone,
I am new to programming on such an embedded device(NRF52840DK). I met a problem recently of how to set up the PIN on the board to connect with the LPS22HB sensor...
According to the doc; * This function will block until the temperature measurement is done. * It takes around 50 us from call to return.
Instead I'd like to return the value...
Hi,
I’m developing an application using the SDK V16 , the nRF52DK (52832) as central, and a couple of Sparkfun nRF52832 breakout boards as peripherals (both peripherals...
Hi everyone!
I am trying to implement the OTA - DFU in my project. I have my own board with a nrF52832 chip.
The project was build using SDK 13.0.0 and softdevice s132...
Dear Nordic Support Team,
I was using the CoAP and MQTT components in nRF5 SDK v16.0 .
So my device was able to do CoAP and MQTT via BLE 6LoWPAN. Adding a BLE service...
I am following the turtorial in the Github and build a project which add a custom service. The project can read, write and notify between the board and mobile nRF connect...
Hello,
I am using a custom nRF52840 ( SDK 14.2.0, SoftDevice S140) based board.
I am using the UART module and associated UART drivers.
Is there a way to ignore the...
I have two nRF9160 DK boards that are programmed with modem firmware version 1.1.1 and are using V1.2.0 sdk software. They also are both programmed with the same mqtt_simple...
Hello,
I want to to configure mesh proxy node and along with that it should also contain relay functionalities using nrf5_SDK_for_Mesh_v4.1.0_src.
Is there any sample...
I'm seeing some issues I don't understand when using RTT. Here is a short fragment of code around the RTT_Write statement.
The commented out statements are included while...
I am using nRFConnect with nRF52840 Dongle. Since the last update to SoftDeviceAPI v5, nRFConnect cannot connect anymore to this specific devices (cheap JDY-10 BT/Serial adapters...
