Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hello Nordic,
I recently setup the Command Line application for our device, using USB CDC ACM. I started experimenting in the example cli project. After everything was...
Using nRF Connect SDK v1.2.0 on nRF52840 DK (PCA10056)
We are evaluating the nRF Connect SDK on the 52840 until our 5340 PDK arrives. While running the mesh light example...
Hi and nice to meet you,
I freshly get my nrf52833 DK. I'm working on windows. I have installed via nRF Desktop all necessary tools.
We are moving our project from nxp...
Hello,
I am trying to connect NRF52832 with another Bluetooth module using custom characteristics. I was able to connect two NRF52832 modules but I can't connect to another...
Hi,
After updating NCS folder to latest Master branch, SES4.52 is not able enter into debug mode.
Receiving error as: failed to set startup compilation break point:...
I have a bootloader, softdevice and firmware (all with sdk 15.0 and softdevice V. 6) on a nrf 52840 on an counter-pcb.
I have upgraded the firmware to sdk 16.1 and use the...
Hello together, I am just starting to work with the nRF9160 and have some problems with the configuration. I inserted the iBasis SIM card and tried to get a LTE connection...
Hi,
I am using a ble_app_blinky example (SDK16) to communicate with the BLE devices. NRF52840 is connected with the client devices and successfully sending the data to the...
Hello,
I would like to know if it is possible to not use softdevice because i need more flash for my code. I guess it is possible but when i don't enable softdevice in my...
Hello,
i'm trying to use SPI with nrf9160DK as master and RFM96 module as slave. At the moment, i'm developing elementary functions to write and read from my slave device...
Hello
I am working on Nordic nrf52832
I am using the "ble_app_blinky_c_pca10040_s132"
I want to use ble for scanning a beacon (eddystone TLM) and collect its data. ...
please help. I need functional description of what is need step by step for doing a zigbee hardware device switch and management over bluetooth on the thingy52, i have all...
Hi Team,
We are using the NRF52840 with s140 Soft device for our BLE application.
While we are facing some issues while doing debugging.
1. We are getting Hard Fault...
Are there any issues of pairing a nRF52833 using OOB pairing with a IOS device? Is there a good example code I could start with?
Thank you very much.
All the best
P...
The system requirements: 50 identical nRF53-based devices (each with a sensor and an actuator), positioned within a 3x3 meter square should be connected to a single computer...
