I have an application that is attempting to use multi-cell positioning based on the results of %NCELLMEAS. The application is following the flow of the NCS positioning module...
Hello,
I have 2 Memfault projects that I'd like to rename, but I can't find any way to do this through the web app, and the API authorization keeps getting rejected (tried...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
Hello. I have been trying to work with extended advertising between two nRF52840 boards using the SDK, but have had trouble in setting a long advertisement payload (as in...
I followed Einar's nRF52840 Dongle Programming Tutorial and tried the ble_peripheral/ble_app_eddystone example using SES 4.12. Opened the project, changed the preprocessor...
Hello All,
I have been using this NRF52 DK board with KEIL for like 2 weeks. I read the all the document regarding BLE 5 protocol and followed the DIY codes step by step...
Hi Sir,
In this project, we design with nRF51822-QFAA (Flash: 256KB, RAM: 16KB) and developed the application and bootloader through the nRF51-DK (pca10028). The file...
Hi Sigurd,
Thank you for your reply. I have executed the code given by you (below link) in Segger studio(V 3.50) I observed that the output or load (pin 31) which is connected...
We have the device, where 2 power supplys can be applied. One of them is external regulator with 3.3 V output. We used it for additional load in our device. Another one is...
Hi,
I referred uart example in nRF SDK 15.0.0 and tried to implement on proxy_client program by adding all files which there in example. but still i'm facing compilation...
Hello!
I'm facing some problems when I try to broadcast a message from my receptor to the transmitters, I'm using 3 nRF24L01P. I read some things about setting the same...
I have 2 PCA10056 preview development boards.
The newer one (0.11.0 2018.3) works as expected.
The older board (v0.9.0 2016.48) the built-in LED1 thru LED4 do not...
I want to use application board and connectivity board with mesh sdk in nordic chip. Is there serialization is available for mesh like using in nRF SDK15.0.0 peripheral driver...
We are developing an application on the nRF52840 kit with SDK 15.2. We are using Keil as compiler. I have started developmet my application with the example ble_app_cscs....
Hi,
I would like to try the DK in a high voltage mode. I tried switching the power source switch to either LIPO or USB (using LIPO battery and USB respectively) but in vain...
Hi, I'm new to thingy, I want to log the data received and viewed in mobile app / web app from thingy 52 development kit which contains nRF52832. Is it possible to log data...
