Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Dear Nordic, I'm using TIMER21 for our library, but I encounter problems with CC channels 6 and 7: their compare events never fire. The problem I configure the timer to generate...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi. The same issue I have is described here, but I've been asked to post a new question:
https://devzone.nordicsemi.com/f/nordic-q-a/29084/why-sd_ble_gatts_exchange_mtu_reply...
I have several characteristics which are updated by a regular timer.
The characteristic property is notify. Due to memory issues I use as value location BLE_GATTS_VLOC_STACK...
Currenetly I access the gpio pins by using this code (P1.01 this pin)
#define PIN_1 ARDUINO_0_PIN
nrf_gpio_cfg_output(PIN_1);
and so on
Is there any other way to define...
I have decided to use nRF52 DK for my project for the first time.
I would like to know what brand of touch screen should be used.
I will use 3.5" and 7 or 10"
Thank...
im bought beacons from this china company (radio land )
the product link : www.radioland-china.com/.../6035982553.html
i could change name or uuid, major , minor with...
Hello.! I try nRF51822(softdevice using S130) SDK v12.3. I operate it as a master, but I leave it to distance to cut once and approach it afterwards, and, after a reconnection...
I need to stream 2 audio channels between two nRF52832 chips. I have two of the nRF52-DK boards and would like advice on which sample app might get me started in the right...
I have used 32khz and 32Mhz Crystal and across that crystal i have used 12pF capacitor. But unfortunately in market 12pF capacitor is not available in 0402 smd package.
...
In the SDK, there are examples for boards called "pca10028, pca10040, pca10040e, pca10056"
I have the nRF52-DK board, which of the above numbers does it conform too? Or...
Hello,
I am trying to adjust a peripheral device to connect a central device based on ble_app_uart_c example. Although this example has been discussed numerous times I was...
I am moving an SDK12 peripheral nus + central nus application to SDK14.
I am following the ble_app_hrs_rscs_relay example for SDK14 on how to setup the dual role ble event...
The nRF52832 OPS 0.6.3 describes the CONFIGID register in FICR. This is the same as on the nRF51822.
SDK 14.1.0 does not show this register in the NRF_FICR_Type definition...
Hi everyone, I've read some nordic forum articles on this topic but somehow I just dont get information I need.
I can flash my custom nrf51822 chip by using my nrf51422...
