Hello,
I have just downloaded the NRF52840 Reference Altium Library.
I have noticed that the step file for the component is not symmetrical about the origin.
If I measure...
We're implementing a PAwR (Periodic Advertising with Responses) based onboarding flow for a large fleet of devices (target: 200+ nodes, eventually scaling to 1000s) and are...
Hello Nordic Support Team,
We are using a Fanstel module that integrates the nRF5340 BLE SoC and nRF7002 Wi-Fi companion IC in a single module.
We have manufactured approximately...
Hello everyone, I'm working on a long-distance communication application (>50m).
My hardware is nRF52840, PA/LNA: RFX2401C, ceramic antenna: AN9520-245.
I've achieved...
Hi:
I use ncs3.3.0 and nrf54l15dk.
PC BLE pairing nrf54l15dk failed log:
prj.conf
But with BT configuration, turning off ESB related content, it can be paired...
Hi, I am developing a program for the nRF54L15 with the DFU bootloader enabled. I would like to reduce the startup current.
I am using SDK 3.2.4.
The `sysbuild.conf` settings...
I am finding it difficult to figure out what is the minimum toolchain requirement to get started developing using the nRF24LE / U.
Is Kiel the only compiler ? Can SDCC...
Hi,
I have nRF51822 DK with (s110_nrf51822_7.0.0, nRF51 SDK_v6.1.0.0) and when i try to run the project in IAR 7.20.2 i receive an error.
2 ) My icf file...
Hi!
I have bought the nrf51822 EV KIT and it came with 5 extra nrf51822 modules but them without a board. I have researched a little and I found that I need the Segger...
Hi,
We're using an off the shelf module with a trace antenna that can't be modified.
Measured the module once assembled, and due to surrounding plastic materials, the...
Just finished upgrading to the latest SDK Version -- and trying to build some of the examples -- but consistently getting compilation errors when building any of the nRF51822...
When working with BLE, one sees a lot of different names for roles, which is confusing. What is actually the difference between them all, master, slave, central, peripheral...
Hello to everyone,
I'm developing a new project with a nrf8002 and a Smartphone with Android 4.4.2. Both devices connect to each other fine, and I can bond them with no...
Hi,
I made a peripheral firmware based on "s110\experimental\ble_app_uart" example, but I don't know how to write a central module FW so that these two can pair to each...
The reset handler as shown in the C:\Keil_v5\ARM\Device\Nordic\nrf51822\Source\templates\arm\arm_startup_nrf51.s will call SystemInit as defined in the C:\Keil_v5\ARM\Device...
Hi
im unable to connect nrf51822 EK with nrfgo studio
how can i solve this issue
m using all latest version softwares
and wen i click ok it shows as below
...
Hello, i know its an often discussed topic but i already read lots of threads about it and didnt find the answer.
I have a simple program that enables the softdevice s110...
Hi,
We are using an nRF8001 with bonding.
We tested the use case were a bond has been established with an iOS app. Then the connection was terminated by closing the...
Hi
am using a thermistor of 10 k with a known resistor of 10 k ,and am giving the voltage divided input to ANI2 (p0.02).The suppply voltage for thermistor is external of...
Hi,
We designed an nrf51822 BLE application using the mbed kit and on-line tools.
Our target pcb has a 1.8V onboard supply. To minimise consumption i want to disable the...
I have an android client that functions as a central and have an app on my MAC (peripheral) that this central connects to and sends data.
At this point, I need to wait...
