Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
we are using NRF52840 , with a SD card. Data is stored in SD card in Text file or .csv file every 10 mins. We want to push the data to Mobile App either using the BLE or using...
about ANCS categoryID 12
I see this website
https://www.linkedin.com/pulse/working-ble-profile-apple-notification-center-service-sarda
have any one know
how to get...
Hi Nordic,
1. Dual Uart this code i used
2. Its working fine and am getting output also
3. But i have doute its printing from uart0 but i want from uart1
4. For that...
Hi,
currently, it seems the CIS bidirectional mode is not supported. I understand that telephony and these profiles then are not able to be evaluated like in a "real setup...
I'm looking to develop a board using the nRF52810 SoC, and am prototyping it on breadboard to start with. The circuit I've set up so far is the same as the reference circuitry...
Hello,
I have been trying to resolve an issue for a few days now. Here is what I'm trying to do.
1. initialize gpiote and tie a pin to an interrupt handler
2. initialize...
Hello folks!!!!
I'm making a similar kind of project available in example and named as ble_app_beacon but the problem is that I'm using PCA10100 board and there's no guide...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v2.0.0
One of my customer expects such a scenario. 1) BLE accept first connection. 2) If BLE have another connection, BLE disconnect...
Hi I m trying to implement mass storage on the arduino nano 33 ble sense board(nrf 52840) and I2c together. I m using the sample from zephyr and it will not mount the file...
I want to install the NCS V2.1.0 with Toolchain Manager V1.1.3. But after I installed, I found that there is only a toolchains folder and a empty .west folder in my intalllation...
hi
I have a question about uart receive.
The UART example receives data based on special characters or the length of the received data to determine whether it is a string...
Hi
We have been using the Online Power Profiler to estimate the current draw from nRF52805 during BLE activity. Especially estimating the potential peak current draw (from...
I bought a nRF52840 DK, and followed the UG for nRF BLE sniffer v4.0.0. I was able to see the sniffer interface in Wireshark on my Linux machine, but when I start capture...
Hello!
I am trying to install MCUMgr on MACos.
I install the Go Programming Language and then follow this: https://docs.zephyrproject.org/latest/services/device_mgmt/mcumgr...
(I was asked to create a new post for this specific query. The original post where this investigation started is here: Async UART and shell module in Zephyr on nRF52480 )...
