I'm having some issues regarding the data update interval when running the asset_tracker_v2 application, particularly with adjusting how frequently it publishes data to the...
Dear Nordic,
it's about USB implementation. We need to add interface string descriptor for ineterface name. Using USBD_STRING_DESCR_DEFINE(primary) I've added that to string...
Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Hello Nordic support team,
Forgive me if I am asking a stupid question.
In the source file ble_conn_params.c, there is a function called ble_conn_params_init() and I...
So whatever I try, the only way to get my idle current consumption to an acceptable low value is to set CONFIG_SERIAL=n in my configuration. But then I don't get printk functionality...
Hello,
I am trying to use an sdcard with the nrf54l15 DK board with the 2.9.1 sdk. However I encounter "<err> fatfs: Storage init ERROR! error: -134" when calling the disk_access_init...
Hello,
I use SDK v2.9.0 with nRF52840 and my application is based on peripheral_uart example.
Have I understood correctly that nRF52840dongle has preloaded (by Nordic...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
My product has nrf52840 with usb mass storage configured using 8MB QSPI flash (same chip as the nrf52840dk - MX25R64)
I would like to allow users to upgrade firmware by...
I am using an nRF52840 USB dongle to sniff some Zigbee packets for a product I am developing. I am trying to use Wireshark to decode the messages shared. I followed the steps...
we have a custom board with nRF9160, when using GNSS we configured it to periodic mode with 120 second interval, most time it works fine but every once in a while (like every...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Dear DevZone,
While porting our project from NCS 2.9.1 to NCS 3.0.0, I ran into linker errors when building LVGL. The linker reports that it cannot find functions defined...
Hello,
I’m currently working on a Bluetooth Mesh project using Nordic Semiconductor devices, and I would like to get guidance on static provisioning and group-based communication...
Hi,
I am using the nRF52840 with nRF-SDK version 16.0.
At random intervals, I encounter the following error:
"[00:02:51.009,460] <error> app: ERROR 1813 [Unknown error...
Hello, I've recently upgraded my pre-production application on nrf52832 from NCS v2.6.2 to Ncs v3.0.1 also upgraded to HWv2(on interim ncs 2.9.0 as adding custom board for...
Hello,
I'm working on a project that uses the Serial LTE Modem (SLM) application on a custom board. The main processor sends data to the nRF9160 over UART. The project is...
Dear Nordic Support Team,
Could you please provide more information on the current status of the Nordic Distance Library ( https://docs.nordicsemi.com/bundle/ncs-latest...
