I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I am using the nRF9160 with the SLM application.
The device will open a TCP connection to the server; the server will always initiate commands and the device reply. So the...
We're trying to synchronise TX and RX in a connectionless direction finding setup. What we want to do is increment a data counter, log this on the TX timestamped, and send...
Greetings to everyone,
The initial data are:
- nRF9160, Hw2, Fw_2023-10-26_1fae141f,
- AT%XSYSTEMMODE=1,0,0,0,
- the device works as expected with the RLC AM.
...
Hi all,
I'm unable to flash my nRF52840_XXAA using the nRF Connect extension in VS Code. My project uses the command:
west flash -d <BUILD-DIRECTORY> --dev-id 1050304532...
Hi, We tried by changing the Tx Power in nrf52840 through the register values as mentioned in the document nRF52840_Product_Specification_v1.10 and Page no 636, but it is...
Hi!
We are in the process of certifying a product using an nRF52840 against EN18031-1 (RED Cybersecurity) where we need to answer details regarding generation of cryptographic...
Hi Is it expected that after calling bt_unpair function disconnected callback is called ? I can't find any information about this behaviour in Zephyr documentation.
Hi:
I'm nRF52832 user from China, tried to download nRF_DeviceFamilyPack of MDK from http://developer.nordicsemi.com/nRF51_SDK/pieces/nRF_DeviceFamilyPack/ failed, i simply...
Hi
I am using nrf Connect sdk 2.9.0 Visual Code IDE.I have added the following configuration in the prg.conf file:
But still I am not asble to receive more than 20 bytes...
Hi Support Team
We want to use the J-Link of nRF54L15DK to program customer's nRF54L15 board. We follow the guideline of below link to connect the Pins of P19 of nRF54L15DK...
Hi, we are using NPM1300 with a ICP401835TPRT renata battery. It has a 10k B=3380 NTC (part number NCP15XH103F03RC ). I'm getting a really high temperature reads and very...
Hi,
I am trying to optimize a time critical device for lowest possible latency data transmission over BLE on nRF5340 working as peripheral. Currently my algorithms are implemented...
I'm adding MCUboot to my application and we'll be using our own app to upload new firmware over BLE to the device over our custom comms protocol. I can use the DFU Target...
Working on a nrf5340 project, and running into limits of the size of the flash to store my application image along with mcuboot bootloader.
I had a mucboot setup that fitted...
