Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hello, I was reading through the documentation for the nRF Connect for Desktop and I came across a reference to set up the nRF Connect for VS Code. However, I couldn't find...
Hi,
I am using nRF52820on a customer board to run MESH Light project, but I can not start the mesh stack, problem is:
it looks like due to flash limited, but according...
Hi All,
I am new to Zephyr/NCS, so I am a little confused about which UART driver (Zephyr's uart/nrf_libuarte/nrfx_uart/nrfx_uarte) to use to approach this feature with...
I'm evaluating the nRF52840_DK with nRF5_SDK_17.0.2
After doing some tests with ppi to timestamp gpio events, I'm now enabling the softdevice.
This leads to two questions;...
I have been successfully using mergehex with s140_nrf52_6.1.0_softdevice.hex and a bootloader to create firmware packages for my nRF52840-based device and wanted to try softdevice...
When I run the QSPI example in SDK, it can work well both on the PCA10056 and my custom development board. However, when I transfer the example to app_buttonless_dfu, the...
Hi,
I am trying to send the max 240 bytes in NUS SERVICE nRF_CONNECT_SDK
I have seen the ble throughput example and changed
CONFIG_BT_RX_BUF_LEN=255
CONFIG_BT_CTLR_TX_BUFFER_SIZE...
Hi Nordic
We are evaluating nRF 9160 for our next revision of the PCB, and we are testing nRF9160DK.
It came with a sim, which i tried to activate by nRF cloud, but it...
Hello
Is there any example or tutorial on how to use the mpu6050 library?
I just started to program the nrf51822 and hope to find some helpful clues to get me going. ...
I have nrf52840/32 dk and lis3dh accelerometer. I have interfaced two of then via I2C. I want to advertise data of lis3dh xyz acceleration values in the ibeacon advertsing...
Hello，
I am testing nrf52840 low power module on usb power supply, but it's current is about 22ua not 7ua.
hardware design
software design
Can you give me some...
Hello,
I'm trying to use `sd_ble_gap_connect` to connect to a peer I discovered using `nrf_ble_scan`.
nrf_ble_scan_init_t scan_init{};
scan_init.p_scan_param = &m_scan_param;...
Hi everyone!
I have already developed a couple projects in nRF52 DK and the result was quite messy. I want to make it right this time and that's why I am requesting your...
According to following function declaration:
an error code should be returned, which indicates reason of failure. However when AF_INET6 is used as ai_family in hints argument...
I'm trying to install the nRF Command Line Tool on my MAC running macOS10.15.6. However none of the avaiable version on the Nordic website will install. Apple refuses the...
