Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello, following this question - https://devzone.nordicsemi.com/f/nordic-q-a/76417/saadc-tasks_calibrateoffset-shall-only-be-used-before-tasks_start-or-after-events_end-nrf52833...
How i'm supposed to check if the device is transmiting any data? I used nRF52833 DK as a sink and node of wirepas mesh network, added another DK and configured it as a regular...
Hi,
I'm making an firmware for the nrf52840 that communicate throw usb to a computer.
First I used the uart library that works fine but required the Jtag and Jling which...
I just cloned the latest zephyr from github and tried littlefs. However, the SPI pins have no traffic and CS line stays unchanged.
Is there something I forgot, since...
Hi, i'm working with NRF51822, and i saw on reference manual that micro enter in the SYSTEM OFF mode. The problem is i dont want the micro enter on this mode.
I make de...
Hi,
I'm working on a project using the gazelle protocol with the gazelle pairing library. Due to the fact that I use the GNU GCC compiler, I created a Makefile from the...
Dear Nordic team,
We have designed custom boards with nrf52840 chip. We observed that in one of the boards the application is not running until the swd pins of the custom...
Hi,
We are using laird BLE653u BLE module in our application. This module has nRF52833 BLE SOC. We have ST Link V2 as a programmer tool. We want to use SWD protocol for...
I have a project using NRF52840 as master in BLE central to scan BLE device.
I found all example will connect device automatically when device found
I would like to change...
Forgive me if this is already discussed somewhere - I'm fairly certain it must have been - but I can't seem to find what I'm looking for. My client's project uses a higher...
Hi,All:
As the topic,which address is the mbr jumping to bootloader by ?0x10000ff8 or 0x10001014? and how to feed the mbr para register 0x10000ffc and the 0x10001018?
Hello,
I need to use the more accurate HFXO for a very short interval to time incoming interrupts (approx 1/50 second every 15 mins)
The processor sleeps idle for the...
Dear DevZone,
I am trying to configure the SAADC on my custom nRF52840 board.
I would like to use it in blocking mode together with oversample 16x and burst enabled...
Why is SES throwing an "Illegal value 0x21009168 written to register 66 (MSP_NS) ignored" message after "Download successful" when programming nRF5340's network core with...
