Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
From the documentation i have found it seems all the nrf52 and the new nrf5340 are all "extended range" up to 105 degrees celcius.
I am evaluating an application where a...
Hello!
Thanks for your help last time, highly appreciated.
However I haven't got till actuall programming because now I can't upload hex files. I start Thingy:91 in boot...
Hi guys,
I just started to work with Nordic boards and I am currently working with Nordic nRF52-DK. I have already installed all the necessary tools that I need to run and...
Hello,
I've been playing around with the nrf52 DK (sdk 16.0.0, s132). I'm trying to add volume up/volume down functionality to the example. I found this source code from...
Hello,
Does anyone has an example of MQTT LST application for nrf9160.
I've tried to use the MQTT_Simple sample with LST.
I've add "CONFIG_MQTT_LIB_TLS =y" change the...
Hi everyone,
I am designing my own PCB using Raytac's module MDBT50Q-1MV2 that carries on the nRF52840 SOC.
The system will operate in normal voltage mode (VDD = VDDH...
Dear All,
I am trying to compile a project from the command line and I want to enable all the warnings possible for the files that I have created. I am using the NCS v1...
hi support team,
i tested the example of \\nRF5_SDK_16\examples\peripheral\usbd_msc , and SD card interface , that with the APP_SDCARD_FREQ_INIT 268435456 (1 M) and APP_SDCARD_FREQ_DATA...
Hi DevZone,
I created my project on SES in order to download files from a web server. So I decided to include in my project the "download_client" library which contains...
Hello! I am working on updating from SDK 15.2.0 to the SDK 16.0.0 and have encountered some problems when trying to use DFU OTA to flash my unit with the application.
I...
I need to be able to measure the battery level of the NRF52 with the internal ADC.
I know it can be done, but I don't really know how to configure it
I am using MBED...
I have purchased an nRF51822 module. I am using the Arduino IDE and the ST link to program the module. I have used the library BLEPeripheral by Sandeep Mistry (see below)...
I deleted a node in the mesh app without unprovisioning the node. I then reprogrammed the dongle hoping that everything will be reset. It seems the dongle is still provisioned...