Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
I've been documenting this issue and asking questions here:
Intermittent device reset in modified ble_app_beacon example
Since I need to post a proprietary schematic,...
Hello,
I was examining the power supply part of the Thingy and I noticed that the charging current is set to 0.5 C, wich is 720 mA (checking XR6804's datasheet it seems...
In order to evaluate the nRF9160 for coming projects, I need to know if it is possible to use Keil as the development platform for the device.
We have a very large codebase...
Hi, May be it's some what basic but I'm not able to update my pwm value. I'm using sdk 14.02 with softdevice in SES. This is my code:
PWM Config:
PWM init:
Update...
fds appears twice in ble_ots:
1. In ble_ots_init:
err_code = fds_init();
2. on_disconnect
err_code = fds_gc();
It does not look like fds is really used in ble_o...
Hello!
I use Segger Embedded Studio. Ubuntu 18.04 I'm trying to build mqtt_publisher project from zephyr samples. And get error: undefined reference to `sys_rand32_get'...
Greetings,
Here are the details:
IDE = SES v4.12
SDK = v15.2.0 and v15.3.0
Hardware = Nordic nRF52 DK (PCA10040 v1.1.1) * 2 and Rigado BMD-300-EVAL * 2 (vB)
I connected...
Can you explain me what I need to do in order to have the esim ? Do I need a physical component ? I am new to this subject if someone can help me a little bit. Thanks
I am trying to measure and characterize expected battery lifetime of my design. I've noticed that as the effective Connection Interval goes up, so does the Rx current peak...
After init I2C channel
#define TWI_INSTANCE_ID 1 // because SPI0 share same reg add with TWI0 we change and enable TWI1
#define MAX_PENDING_TRANSACTIONS 5
NRF_TWI_MNGR_DEF...
Hello,
I am trying to estimate Battery life. I am using CR2032 with 230 mAH capacity. I am confused with the calculations.
As per excels sheet in below link, for 500...
Hi, I have strange problem using pc-ble-driver on nrf52 with heart_rate_monitor example. When I set advertisement data to be 16 bytes long, two of our testing phones cannont...
Hi,
I am using nRF52832 and I need to create a timer interrupt handler, which can trigger at 417us (microsecond). I am using Segger Embedded studio. Please, can anyone help...
I have a project which recently started logging the following error on boot.
nrf_sdh_ble: sd_ble_enable() returned NRF_ERROR_NO_MEM.
This is the only log message....
Hello
I have a simple Thread network with 3 nodes and I would like to send a provisioning request from one to the 2 others in order to get their IP.
I modified the Thread...
