nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hi all,
I am running the lsm6dso zephyr sample on my nrf52833 dev kit. I am unable to set the sampling frequency. I get this error after flashing:
This is my overlay...
I am using the nRF9160 with the SLM application.
The device will open a TCP connection to the server; the server will always initiate commands and the device reply. So the...
We're trying to synchronise TX and RX in a connectionless direction finding setup. What we want to do is increment a data counter, log this on the TX timestamped, and send...
Greetings to everyone,
The initial data are:
- nRF9160, Hw2, Fw_2023-10-26_1fae141f,
- AT%XSYSTEMMODE=1,0,0,0,
- the device works as expected with the RLC AM.
...
Hi all,
I'm unable to flash my nRF52840_XXAA using the nRF Connect extension in VS Code. My project uses the command:
west flash -d <BUILD-DIRECTORY> --dev-id 1050304532...
Hi, We tried by changing the Tx Power in nrf52840 through the register values as mentioned in the document nRF52840_Product_Specification_v1.10 and Page no 636, but it is...
Hi!
We are in the process of certifying a product using an nRF52840 against EN18031-1 (RED Cybersecurity) where we need to answer details regarding generation of cryptographic...
Hi Is it expected that after calling bt_unpair function disconnected callback is called ? I can't find any information about this behaviour in Zephyr documentation.
Hi:
I'm nRF52832 user from China, tried to download nRF_DeviceFamilyPack of MDK from http://developer.nordicsemi.com/nRF51_SDK/pieces/nRF_DeviceFamilyPack/ failed, i simply...
Hi
I am using nrf Connect sdk 2.9.0 Visual Code IDE.I have added the following configuration in the prg.conf file:
But still I am not asble to receive more than 20 bytes...
Hi Support Team
We want to use the J-Link of nRF54L15DK to program customer's nRF54L15 board. We follow the guideline of below link to connect the Pins of P19 of nRF54L15DK...
Hi, we are using NPM1300 with a ICP401835TPRT renata battery. It has a 10k B=3380 NTC (part number NCP15XH103F03RC ). I'm getting a really high temperature reads and very...
Hi,
I am trying to optimize a time critical device for lowest possible latency data transmission over BLE on nRF5340 working as peripheral. Currently my algorithms are implemented...
I'm adding MCUboot to my application and we'll be using our own app to upload new firmware over BLE to the device over our custom comms protocol. I can use the DFU Target...
