I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi Nordic Dev team, I'm using the older nRF SDK in a project that is built using a nRF52840. I have an RTC and a GNSS connected to the nRF52840. I use one of the LP timers...
Hi,
We are ready for the production of the 9161 and we have applied for the IMEI by the nRF cloud. The IMEI we have applied are all 15 and we want to know if the IMEI's...
We developed a custom board with an nRF9161. During board bringup I want to test if the modem can connect via Cellular. I flashed the modem_shell firmware. The modem reports...
In our application, if i enable Softdevice with LF clock Source as RC i get proper timing on interrupts.
If i remove softdevice and just request lf clock manually, the...
Hi All!
I want to procure the nrf9160DK for my project. Can you please guide me that nrf9160 LTE services will work in Pakistan? The cellular mobile operators in Pakistan...
Hi,
I am currently working on communicating between the nRF5340 DK and the nRF5340 Audio DK over BLE. Could you please share the information flow?
Warm regards, Rajendra...
Hello.
I am developing device using nRF52840 and i have question about IO pin usage.
The circuit is currently providing voltage to the A12 pin (Digital I/O), but it is...
Hi,
I'm using a Azure IoT Hub to connect some devices to the cloud and then uses the Direct Method to send messages to the devices. I can send messages and receive the response...
We are using nPM1100 along with a STM CPU. When we put the CPU into deep sleep, it takes one minute for the current to go down to 20uA from 500uA.
We were expecting the...
I have a customised bootloader using uart + BL, built from the SDK examples and modified using articles found here. It works - most of the time. The product is a cusom board...
Hi to all,
this is my first public ticket ;)
I would power a nRF52840 on my custom board both with a cell battery (specifically CR2032) and the VBUS provided by the USB...
Hi, 1. After executing nrfjprog --recover command with PCA10040 DK, I read this hex: nRF52832.hex with Programmer
2. What does this program do that causes read protection...
I have successfully implemented an interrupt-driven method to read data from the MPU6050 sensor on the NRF52840, and it functions as expected. However, I encounter an issue...
I've been playing around with the advanced_non_blocking_internal_timer example, on my nRF52DK-52832 board using NCS 2.6.0.
I couldn't get it working for what seemed like...
Is there a solution from Nordic available where I can have a LTE-M (or NB-IoT) and at the same time still receive the 1PPS output from the GPS module? It seems to be that...