I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi,
I am using 5340 but it's uart consumes a lot of power 2.01mA
SDK: NCS2.1.0
project: peripheral_uart
I have disabled all other peripheral equipment,put all...
when I open nrf connect for desktop i got blank page,
and there nothing in the console:
I've installed/am using:
nRF Connect for Desktop v.3.11.1
J-Link V7.68b...
Hello,
we are using the nrf9160 in one of our products. Our assembler has used old nrf9160 SICA B0 chips on our first protoyping round. When we run our software on the nrf9160...
Hello, Guys.
I had problem that if I config nRF9160 through UART0 (default) it works and I receive IP address and can make MQTT connections.
But when I use UART2 (external...
Background:
I seek to interact (human and/or additional MCU) with both UART peripherals (uart0 & uart1) in the easiest manner possible - issue commands, pass traffic, etc...
I have shell working with the following configuration
CONFIG_SHELL =y
CONFIG_SHELL_BACKENDS =y
CONFIG_SHELL_BACKEND_SERIAL =y #also selects serial
CONFIG_SHELL_CMDS...
Check the below C++ code:
in file S.h, we define class S
in file S.cpp, we implement S constructor and function init()
in file test.cpp we first declare a global...
Hello there,
I am looking for a way to connect to the Eclipse Leshan Server without DTLS using the LwM2M Client sample. However, this does not seem to be so easy.
The...
I try to run nrf sniffer with Wireshark.
I flashed sniffer_nrf52840dongle_nrf52840_4.1.0.hex
I download and run nrf_sniffer_ble.py.
I got this error and I cannot find...
Hi all,
For a project I need to use a private library which uses the app_scheduler to queue events triggered from a second MCU. I am using FreeRTOS on the nRF and I am unsure...
Dear Support,
as suggested I create specific question based on this thread:
Could you please confirm that the QSPI peripheral makes polling of QSPI flash Status Register...
I was trying to implement the nRF5_SDK_17.1.0_ddde560 proximity example into the template.
After getting all the functions working and the application compiling, the board...
For some reason the microprocessor will not wake when P0.07 is pulled low. I have an external 10kOhm pullup so there is no need to configure the internal pullup. If I change...
Hi! I've been struggling with a bug on a nrf51822 product I'm working on. It features some I2C devices, a screen and a couple of sensors. The mcu gets a watchdog reset due...
In my application (built with NCS v1.7.0) I use a nonblocking TCP socket for communication. The main modem thread handles sending data and a separate thread handles receiving...
