Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Hi,
I am following below link for DFU over BLE. Link ( https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu ) currently it is working fine...
Hello ,
I'm using the libuarte library so i can send data and receive it , i'm enabling RTC2,TIMER1,TIMER0 and TIMER2 .
this is the main definition of my libuarte NRF_LIBUARTE_ASYNC_DEFINE...
I'm running into an odd problem with the PWM driver. We're using SDK 17.0.2 and the S113 softdevice on an nRF52833. We're using the PWM module to drive some LEDs.
The nRF52833...
1. nRF Connect SDK v1.9.1
2. Segger 5.68
3. sample name : multiple_adv_sets
I am developing through multiple_adv_sets.
I want to test by changing the uuid in uuid...
Hello
I have installed NRF Connect for Desktop in my system (64bit, i3 CPU). I want to debug my custom hardware using the nRF9160 Development Kit. I have connected the nRF9160...
We have a big application bigger than 500ko and we need a littlefs partition, so we end up with a mcuboot_secondary smaller than the mcuboot_primary (actually we put it to...
Hello, as stated in the Titel im trying to read Firmware Information, for Example the Firmware Version. I tried solving this by reading via Flashareas but no matter where...
Hi,
Datasheet says the sequence as mentioned below,
But the code given in the nordic playground does not follow the sequence mentioned in the datasheet, and the code...
Dear members, with success I implemented the time synchronization example from the nRF5 SDK guide. This example works perfect for a single master, but what if the master changes...
Hi Nordic:
How to use GZLL in nRF52833.
It is only has PCA10040 and PCA10056 In "gzll_ack_payload", but nRF52833 is PCA10100.
I try to use PCA10040 run in nRF52833,...
I start learning open thread in nrf connect SDK using nrf52833, it was pretty fun examples. Now I switch from using cli to send udp from/ to devices to implement it in the...
Hello everyone,
I'm having some issues working with the nRF Connect for VS Code extension in combination with the nrf_desktop application demo from the nRF Connect SDK....
Hello,
VSCode, i change NCS1.9.1 to v1.9.99,
restart computer,but got error:
OUTPUT can not use compilerPath“D:\Program\v1.9.1\toolchain\opt\bin\arm-none-eabi-gcc.exe...
Hello,
I am working with a TOF sensor, and in the init I need to upload some firmware through an I2C connection. It functions as intended when it is a smaller amount of...
