I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
I would like to use the low power pwm library to get a breathing LED effect on my device. The MCU I am using is a BMD 350 and the LED is connected to nRF52 port P0.02.
...
I want to protect the programme and data in the flash memory from being rewritten during shipment.
I thought that I could set the NVMC register, CONFIG, to read-only, so...
today in the morning I can connect this web site via chrome.
but I cannot connect this web site few hours later with banned my ip page.
I don't understand.
my system...
I am working on a project that requires serial DFU without flow control using nRF SDK 17.1.0 running on the nRF52840 without the soft device as I don't need BLE for this application...
We are investigating the use of the Soft Device Controller as an alternative to a Soft Device for our production product. Using our BLE stack we have successfully completed...
I'm using SDK 17 with the nRF52840-DK.
As a starting point for my application, I'm using the .../examples/ble_peripheral/ble_app_hrs_freertos project since shows the proper...
Hello, I would like to make a follower robot. For this, I wanted to use the AoA to locate my phone and thus determine the direction in which the robot should go.
I'm really...
Hello,
I am working with a nRF5340 and need to use both CDC and mass storage on SD Card. I started my application based on the CDC example and it has worked fine.
Now...
Hello,
NCS1.9.1, VSCode, nRF52840,
from link UART Driver – Nordic Developer Academy (nordicsemi.com)
uart can't to receive data continuously,
receiving evt->data.rx...
Hello,
I am working on nRF52840 DK and dongle. I am trying to implement a firmware that can scan device and send command through NUS. So I use ble_app_interactive example...
So, this could just be an odd coincidence, but I'm stuck.
I had a project working using standard advertising. You connect, pair, and then the client (nRF Connect on Android...
Hi! I'm trying to encrypt some data using ECC 256 but I have some issues:
-I found a code ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrf/samples/crypto...
Hello! I'm trying to use a custom SPM using this guide: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/using-a-custom-secure-partition-manager...
I closed the previous discussion by mistake: https://devzone.nordicsemi.com/f/nordic-q-a/83067/nrf9160-board-for-qr-code-project?ReplySortBy=CreatedDate&ReplySortOrder=Ascending...
Hi there
The project that I am focusing on was really time-critical, so I'm wondering whether we could disable Link Layer ACKs in nRF Connect SDK (i.e. Zephyr) ? If not...
