I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hello
While converting from nRF52832 to nRF52810, we found a problem that the SEGGER compiler returns with the message
section '.init' will not fit in region 'UNPLACED_SECTIONS...
Bluetooth didn't have a standard for transmitting audio using LE until LE Audio was released. And many manufacturers which produced BLE remote controls used Voice Over HID...
In my project, nrf9160 has to send and receive data from the I2C bus from a chip. Everything works fine but unfortunately I have to query the chip by sending a single byte...
Hi,
I'm using nRF52840 DK to construct and test a wireless data transmission system.
The problem is that I need to detect a 2M Hz clock's rising edge using nRF and...
Dear Community,
we are looking into an application where the Gateway (RX) uses the nRF5340 + antenna array and the clients (TX) the nRF52840. The clients are on the market...
Hi, we are trying to characterize RSSI and TX output power with nRF52-DK board.
We used a nRF52-DK (TX) and 2.4-GHz BLE antenna (chip-type, RX) was connected to spectrum...
Dear Nordic Team,
After updating the modem firmware to the latest available (mfw_nrf9160_1.3.0), my device LED does not come up anymore. Additionally, I can longer see my...
Hello, I am trying to use open-thread with NRF52840. There are two different SDK one of them is NRF-SDK for Thread and Zigbee and other one NRF-Connect. Nordic recommends...
Hi
I was wondering if using sd_ble_gap_rssi_start to measure RSSI value during connection has any influence on power usage or ble data throughput (or other resources). Or...
Is there any way to programatically set the 51822 into debug mode following a power on reset, or disable pin reset in normal mode?
Here is a synopsis of the issue:
...
For my project in development I need to read characteristics from BLE devices using pc-ble-driver library.
I am using a C program, not python bindings.
The method I am...
Hello, I am using Nrf52832 and want to run client and sever simultaneously. I think it's possible but unable to find the sample code. Can you please help?
Thanks
Hi, in my custom nRF52805 peripheral application, I used Nordic NUS Service to transmit sensor's data. By using SDK17 example code <ble_app_buttonless_dfu>, I could OTA DFU...
