Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Hi,
I am trying to send messages from my gateway, which has UART and __LOG enabled, to a specific LPN address (0003).
So I want to send messages from my FN Light1 (0002...
We have developed an application in ncs-1.3.0 where we created a west.yml file for the application that lists nrf, zephyr and other dependent repositories. We have downstream...
Hello. everybody.
I'm new to be here.
Now, I'm struggling to succeed in building 'ble_app_beacon_pca10040_s132.uvprojx'.
(This file located in C:\(private dir)\nRF5_SDK_12...
We encounter 52810 freezing problem. It occurses in low probability less than 1 out of 1000.
Power-on reset is no use for this problem. The freezed 52810 chip restored when...
Hello,
I am developing a product that acts as a peripheral and sends a notification of more than 20 bytes (which is by default the BLE MTU). How can I config the MTU so...
Hallo I'm writing Data to the I2C port.
I'm using the nrf_drv_twi_tx function. It works well.
But I want to write bytes to the I2C without Adress. - i want to write just...
Hi,
I have the nrf5340 development kit. This is my first time working on Nordic devices. I've followed the Getting Started Guides. I am trying to run the first test. My...
Hi,
I'm trying to m ake sure that the nRF Sniffer files can be run correctly, following the instructions: "On Windows, type nrf_sniffer_ble.bat --extcap-interfaces".
The...
Hi,
Can you please explain what is the usage of unconnectable advertising? And what is the difference between beacons and unconnectable advertising?
Thanks!
What does (15U) mean ? Is that a specific useage declaring a number?
What does " =='\n' " means ?
After a long period of learning , I'm now trying to read and understand...
Hi everyone,
I am making a zigbee mesh with just coordinator and routers only. I intended to have the mesh to cover a very large areas with nodes that can be moved (not...
Hi,
I have got some problem of understanding the IQ sampling data.
As below is the official data format
0: I_Q (default)
Q
31:16
12 bits signed, sign extended...
I have successfully installed the drivers and downloaded the latest firmware version, but the connexion fails and I can not use the AT interfaces command for the modem controller...
Hi
I am using an example project written for pca_10040, I am trying to replace it with pca_10010.
So far, I changed the "Target Device" in the project options and the...
Hi all,
Currently we are trying to measure the power of nRF52832 using (1) nRF52 DK board, (2) power profiler kit 2 (PPK2).
We used PPK2 in source-meter mode and we connected...
