I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hello,
I am using nRF52840 chipset and I was using the Segger tool chain properly. But recently I started getting below error "The evaluation period of this release has...
Hi,
I am doing the project in nRF2832 , where I need to collect some data from the sensor and temperature value that i need to save in the .CSV file format in SD cARD ....
Hi,
I have a question about setting the gpio pin status. From the picture, it seems that the value on the right represents the status of the gpio pin. So the default value...
I'm using NCS 1.4.0 and 2 boards nRF5340PDK.
I'm using central_uart and peripheral_uart samples. Both display when connection interval change.
The central_uart use BT_LE_CONN_PARAM...
can You explain
light_lc_client_light_onoff_set(&m_clients[0], &set_params,&transition_params);
This command in the lc client used to make the immediate on the server...
I'm implementing a project that attempts to change the TX power of itself during runtime. I have used the set and get functions from the Zephyr sample: https://docs.zephyrproject...
Hi guys, Do we have an outlook on silicon in which errata bugs 174, 195 & 198 (SPIM3 bugs) are solved?
Best regards,
Casper van Doorne
Pink Fluffy Unicorns BV
I am trying to make the LSM9DS1 connected with the nrf52840,
1. Now I am trying to send the hex array to the lsm9ds1, seems always failed.
any suggestion how to make...
Hi,
In my aplication, I bring my nRF52840 into power system off mode with s d_power_system_off on several different events, most notably the BLE_GAP_EVT_DISCONNECTED event...
Hi Team,
We have developed an application where we are able to receive scan request notification in peripheral and scan response notification in central.
Is it possible...
Using the nRF Connect SDK from Nordic Semiconductor is a terrible experience. One reason it being unreliable with many broken samples. And another being the Segger Embedded...
HI,
I'm using Nrf52840 device and connecting my mobile.
After inserting the authentication code for the pairing process.. phone connects successfully and after a few seconds...
Hello,
I wanted to confirm my understanding of the Replay protection cache. In the code, the limit is set to REPLAY_CACHE_ENTRIES and there is a note that says:
@note...
Hi to all.
I am new to this forum and to the Nordic range of products.
My experience over the last few months have been with arduino and Feasycom bluetooth modules. I...
Hi,
Since I updated nRF connect from 3.6.0 to 3.6.1, I get this error when I try to connect to a device :
"Error when getting device info: Error: Error: Error occured...
